Anycubic Photon Printer Owners 造訪社團

原文網址 Ron Bamber
2019-08-10 13:56:54

can any one tell me what sort of UV light I should get any recommendations in the uk thanks

翻譯年糕

Mark Wardle
2019-08-10 21:33:59

Ron Bamber
2019-08-10 21:50:58

Mark Wardle
2019-08-10 21:58:48

Mark Wardle
2019-08-10 22:01:20

原文網址 Kent Dustin Navarette
2019-08-10 13:54:49

Can denatured alcohol clean resin same as isophrophyl? Thanks!

翻譯年糕

Eric Jorgensen
2019-08-10 13:55:34

Kent Dustin Navarette
2019-08-10 14:00:47

Eric Jorgensen
2019-08-10 14:06:33

Kent Dustin Navarette
2019-08-10 14:08:26

Eric Jorgensen
2019-08-10 14:10:01

Eric Jorgensen
2019-08-10 14:12:24

Richard Russell
2019-08-10 14:25:20

Eric Jorgensen
2019-08-10 14:26:50

Joe Estrada
2019-08-10 14:28:29

Eric Jorgensen
2019-08-10 14:32:46

Richard Russell
2019-08-10 14:33:33

Kent Dustin Navarette
2019-08-10 14:56:22

Kent Dustin Navarette
2019-08-10 14:56:28

Kent Dustin Navarette
2019-08-10 15:13:57

Joel Reid
2019-08-10 19:02:56

原文網址 Peter Jarvie
2019-08-10 13:31:47

My photon comes today is there any tips to help the set up process and first print go well please My photon comes today is there any tips to help the set up process and first print go well please 翻譯年糕

Eugene Royzengurt
2019-08-10 13:36:00

Billy Thiex
2019-08-10 13:48:11

Ryan Dove
2019-08-10 23:14:35

Peter Jarvie
2019-08-11 00:21:43

Ryan Dove
2019-08-11 00:28:45

Peter Jarvie
2019-08-11 00:35:54

Ed Gaulton
2019-08-11 09:07:09

Tim Moulton
2019-08-11 12:03:37

原文網址 Theodore Garcia
2019-08-10 13:04:25

Printed this for a buddy.

翻譯年糕

原文網址 Mata Mac Gille Fhionntain
2019-08-10 12:38:34

Not a big fan of the green due to the difficulty of seeing details.

I do not have any shaker/mixing equipment. So just manually.

Thinking i'll warm it up a bit, shake, then run through the vacuum chamber to clear any bubbles and it should mix it a fair bit more in the process.
Am I missing anything in my process?

翻譯年糕

Rigo Arevalo
2019-08-10 12:44:26

Mark Wardle
2019-08-10 12:56:27

Scott Clark
2019-08-10 12:59:12

Jared Zadorozny
2019-08-10 13:43:48

Jared Zadorozny
2019-08-10 13:44:13

Jared Zadorozny
2019-08-10 13:45:28

Jared Zadorozny
2019-08-10 13:50:50

Matt Mason
2019-08-10 14:26:03

Gary Houser
2019-08-11 10:08:20

Deb Longoria
2019-08-11 11:30:11

原文網址 Chad Elstad
2019-08-10 12:28:56

Guilty. There's also a set of Strawbarians. ;)

翻譯年糕

原文網址 Danny Rosenthal
2019-08-10 12:23:16

After a week of frustrating trial and error I finally found the best settings and got my build plate leveled correctly. At .05 layer height, I think my prints are starting to look pretty good. Thanks everyone for the advice and help!

Elegoo Gray
.05 Layer Height
10s exposure; 100s bottom

翻譯年糕

Aditya Chauhan
2019-08-10 14:05:36

Tauri Icenogle
2019-08-10 14:20:32

Mark Wardle
2019-08-10 22:14:01

原文網址 Teek Cooper
2019-08-10 12:01:02

Do any Australians have a reliable source for Elegoo Resin. Trying to test a few varieties but can seem to get hold of it.

翻譯年糕

Robert Sakaluk
2019-08-10 12:11:28

Robert Sakaluk
2019-08-10 12:12:48

Teek Cooper
2019-08-10 12:39:08

Greg Chapman
2019-08-10 12:45:04

Teek Cooper
2019-08-10 12:52:26

Greg Chapman
2019-08-10 13:03:09

Billy Thiex
2019-08-11 03:06:32

原文網址 Stefan Ritchie
2019-08-10 11:29:11

Top 3, cured without washing.
Bottom 3, cured after washing.
All 6 parts printed directly on the build plate.
Nothing amazing, but an interesting case, I think.

翻譯年糕