Anycubic Photon Printer Owners 造訪社團

原文網址 Bobby Bonner
2019-06-12 02:46:34

Can I see examples of people's curing setups using LED strips?

翻譯年糕

Chad Elstad
2019-06-12 02:52:09

Bobby Bonner
2019-06-12 02:54:14

Chad Elstad
2019-06-12 03:26:35

Guillaume Gendrot
2019-06-12 03:27:50

Jeff Johnson
2019-06-12 05:46:45

Stephen Farrell
2019-06-13 15:10:12

Bobby Bonner
2019-06-18 08:39:57

Chad Elstad
2019-06-18 08:49:05

原文網址 Alex Clarke
2019-06-12 02:42:22

When your so confident you buggered up your fep replacement you buy a backup off amazon the same day. Lol

翻譯年糕

Daryl Allman
2019-06-12 02:52:52

Michael McElrath
2019-06-12 03:07:38

Alex Clarke
2019-06-12 03:08:58

Michael McElrath
2019-06-12 03:09:24

Michael McElrath
2019-06-12 03:09:49

Alex Clarke
2019-06-12 03:10:55

Michael McElrath
2019-06-12 03:24:26

Michael Szita
2019-06-12 03:27:16

Eric Jorgensen
2019-06-12 03:45:55

Alex Clarke
2019-06-12 11:39:45

Richard Thomas
2019-06-14 20:23:05

原文網址 Daniel Lilygreen
2019-06-12 02:23:29

Nick Williams
2019-06-12 04:06:35

Daniel Lilygreen
2019-06-12 04:10:15

Nick Williams
2019-06-12 04:11:00

Nick Williams
2019-06-12 04:11:18

Daniel Lilygreen
2019-06-12 04:11:32

Nick Williams
2019-06-12 04:11:57

Daniel Lilygreen
2019-06-12 04:12:22

Nick Williams
2019-06-12 04:12:45

原文網址 Andy Chung
2019-06-12 02:14:48

Can i assume that this is a leveling issue? This was supposed to be a whole leg

翻譯年糕

Chad Elstad
2019-06-12 02:16:37

George Bulte
2019-06-12 02:20:22

Chris Rees
2019-06-12 02:20:45

Andy Chung
2019-06-12 02:34:23

Stefan Giudici
2019-06-12 02:45:35

Sven Zethof
2019-06-12 02:45:38

Stefan Giudici
2019-06-12 02:46:08

Andy Chung
2019-06-12 04:38:31

Sven Zethof
2019-06-12 04:54:48

Sven Zethof
2019-06-12 04:55:06

Charlie Anderson
2019-06-12 04:59:51

Marvin Tomizzi
2019-06-12 21:01:07

Ike O'Ohiocaigh
2019-06-13 00:42:38

原文網址 Tony Rooney
2019-06-12 02:04:58

So, I just updated my firmware (following some problems outlined in the "Known Issues" guide on Photonsters), but I just was wondering what the naming convention is?

Is 4.2.3 an earlier release than 4.2.12? Or a more recent one?

翻譯年糕

Jarrod Smith
2019-06-12 02:26:47

Tony Rooney
2019-06-12 02:32:40

原文網址 Amanda Kennedy
2019-06-12 02:04:17

Any advice please on where I'm missing the logical solution?? I've tried placing the hole in a few different place but keep failing ?

翻譯年糕

Bob Deblier
2019-06-12 02:36:18

Bob Deblier
2019-06-12 02:38:09

Amanda Kennedy
2019-06-12 02:39:57

Amanda Kennedy
2019-06-12 02:41:10

Amanda Kennedy
2019-06-12 02:44:00

Bob Deblier
2019-06-12 03:02:36

Amanda Kennedy
2019-06-12 03:05:08

原文網址 Jorge Ramirez
2019-06-12 02:02:32

Hola owners cómo están? Me pasa que las estructuras que imprimo se aplastan de la cara que va hacia la luz.ayuda por favor

翻譯年糕

Jaime Cuéllar López
2019-06-12 02:52:19

Jorge Ramirez
2019-06-12 05:06:00

Jaime Cuéllar López
2019-06-12 05:25:31

Jorge Ramirez
2019-06-12 11:15:28

Jaime Cuéllar López
2019-06-12 12:57:57

原文網址 Victoria Elizabeth Eden
2019-06-12 01:43:58

Hi all, hoping to get some advice. I'm looking to use photographs/footage from a drone to build a terrain model, do any of you use any photogrammetry software, and what to you think is the best?
Thanks in advance ? Hi all, hoping to get some advice. I'm looking to use photographs/footage from a drone to build a terrain model, do any of you use any photogrammetry software, and what to you think is the best?
Thanks in advance ? 翻譯年糕

Alessandro E. Danti
2019-06-12 02:06:07

Victoria Elizabeth Eden
2019-06-12 03:16:17

Alessandro E. Danti
2019-06-12 04:01:20

Tim Allen
2019-06-12 05:14:44

Nick Neal
2019-06-12 09:35:00

Victoria Elizabeth Eden
2019-06-13 16:08:24

Chris Yarrow
2019-06-14 05:00:34

Victoria Elizabeth Eden
2019-06-14 13:18:14

原文網址 Robert Thorhauer
2019-06-12 01:42:08

Hey Folks! What kind of Pliers and/or Pincers you use to remove the supports? Any other Tools you may use to further grind down the models support bases?

翻譯年糕

Thomas Mccafferty
2019-06-12 01:42:55