Anycubic Photon Printer Owners 造訪社團

原文網址 Bogdan Preda
2019-05-18 16:53:55

13cm tall ? ? . I’m thinking the darker spots are still not fully cured?

翻譯年糕

Bogdan Preda
2019-05-18 16:55:55

Niall Forrester
2019-05-18 17:09:17

原文網址 Susan Sioux Mercer
2019-05-18 16:16:32

New color test with Elegoo Grey with ink and a touch of irridised pigment, but I forgot to re-stir it before printing, so the powder is mostly on the bottom :P
EDIT- I should remark that the loss of detail is because this was a test piece of the new AA Firmware, run at AA8.

翻譯年糕

Zena Andreou
2019-05-18 20:53:00

Paul Michael
2019-05-18 20:59:53

Susan Sioux Mercer
2019-05-18 21:05:49

Susan Sioux Mercer
2019-05-18 21:08:05

Zena Andreou
2019-05-18 21:10:48

Nick Williams
2019-05-18 23:06:50

Susan Sioux Mercer
2019-05-18 23:17:15

Philippe Maegerman
2019-05-19 03:18:47

Philippe Maegerman
2019-05-19 03:19:28

Susan Sioux Mercer
2019-05-19 03:25:13

Susan Sioux Mercer
2019-05-19 03:25:56

Philippe Maegerman
2019-05-19 03:27:12

Susan Sioux Mercer
2019-05-19 03:32:25

原文網址 Susan Sioux Mercer
2019-05-18 16:12:51

Ok, so I had printed the greenish-gray (grayn?) one last week. I used the exact same file for the purple one, just sliced with AA8. What little difference I see is the purple one has less detail. Too little detail for my taste.

翻譯年糕

David McGyver
2019-05-18 17:39:41

Susan Sioux Mercer
2019-05-18 17:42:33

伟洪
2019-05-18 20:39:39

Susan Sioux Mercer
2019-05-18 20:54:51

Anh Hoàng
2019-05-18 21:05:45

Richard Shapiro
2019-05-18 21:59:51

Susan Sioux Mercer
2019-05-18 22:06:14

Richard Shapiro
2019-05-18 22:15:40

Justin Elliott
2019-05-18 22:16:38

Richard Shapiro
2019-05-18 22:17:40

Rod Williams
2019-05-18 22:50:00

Eric Gauthier
2019-05-18 23:46:49

Tero Konttila
2019-05-19 00:10:31

原文網址 Jesper Lindhardt
2019-05-18 15:45:21

Hi' can someone please explain to me how does the Off time, Z lift and Z speed influent on the print ?? when do i have to change it ? Right now im runnig thru my first 250ml Green resin with standart settings from AC and the first 6 prints is 100% spot on. But if i change to another coulor do i then have to change these parameters? I know that the Light on time has to fit different resin, but i can't find anything about the other parameters.. Thx and let's print :-)

翻譯年糕

Marco Wintermayr
2019-05-18 15:50:37

Devin Wallace Simonsen
2019-05-18 16:02:36

Niall Forrester
2019-05-18 17:14:39

Richard Thomas
2019-05-18 18:19:33

Devin Wallace Simonsen
2019-05-18 18:21:01

原文網址 James Brosman
2019-05-18 13:55:09

Could I use this for curing?

翻譯年糕

Andre Ribeiro
2019-05-18 13:57:20

Richard James Sanchez
2019-05-18 13:57:31

Nemipuka Nem
2019-05-18 13:57:34

James Brosman
2019-05-18 14:00:14

Dominick Trascritti
2019-05-18 14:01:30

Terry Burlison
2019-05-18 14:02:13

James Brosman
2019-05-18 14:02:37

Dominick Trascritti
2019-05-18 14:04:08

Adam Widdowson
2019-05-18 15:58:47

Wm Kuch
2019-05-18 17:42:35

Wm Kuch
2019-05-18 17:45:46

Thomassen Ølf
2019-05-18 20:55:36

Brian Sam Antics Posteraro
2019-05-18 22:36:56

Marc Schmidt
2019-05-18 23:32:43

Brandon Marcussen
2019-05-19 03:07:32

Jeff Johnson
2019-05-19 05:37:19

Adam Widdowson
2019-05-19 05:39:13

原文網址 Mata Mac Gille Fhionntain
2019-05-18 13:52:22

Deciding on a cool model to print in Elegoo clear. Any tips on a good finish for using clear resin? Deciding on a cool model to print in Elegoo clear. Any tips on a good finish for using clear resin? 翻譯年糕

David Nicholls
2019-05-18 14:24:51