Anycubic Photon Printer Owners 造訪社團

原文網址 Nick Sugg
2019-03-01 21:27:23

Does anybody know of any High temperature resins that can handle 200+ degrees Fahrenheit? 350+ would be ideal

Chad Elstad
2019-03-01 21:27:57

Richard Thomas
2019-03-01 21:38:32

原文網址 Seona van der Pol
2019-03-01 21:00:46

I’m sorry, but chitubox sucks. I used heavy support, I used a lot of them, the print stuck fine to the build plate, no leveling issues, and fell off the supports. I have never had this happen with the photon slicer supports. Not to mention the 2 days I spent cleaning up the pixel artefacts generated by the slicer in the validator program. Back to the default slicer I go. ?

翻譯年糕

Per Bekker-Madsen
2019-03-01 21:18:17

Nikolas Willingham
2019-03-01 21:24:36

Colin Graham
2019-03-01 21:29:04

Nick Porterfield
2019-03-01 21:40:42

Giancarlo Arriola
2019-03-01 22:38:05

Sherri Leyden
2019-03-01 22:39:25

Yelena Novikova
2019-03-01 22:45:43

Shawn Atlas
2019-03-01 22:46:15

Chris Kaczmarczyk
2019-03-01 23:17:39

Taeo Gerrits
2019-03-02 03:08:00

Jesse Stenner
2019-03-02 03:11:53

Jannick Langfahl
2019-03-02 03:54:10

Nick Williams
2019-03-02 04:24:27

Peter Ede
2019-03-02 06:28:49

Sen Kun
2019-03-02 07:16:40

Dustin Scott
2019-03-02 09:24:25

Susan Sioux Mercer
2019-03-15 22:27:45

Sen Kun
2019-03-16 05:25:45

Susan Sioux Mercer
2019-03-16 23:10:46

Muhammad Zulkhairol Yacob
2019-03-18 04:25:25

Muhammad Zulkhairol Yacob
2019-03-18 04:25:53

Sen Kun
2019-03-18 04:30:14

Muhammad Zulkhairol Yacob
2019-03-18 05:23:23

原文網址 Chris D'Andrea
2019-03-01 20:54:22

I know i should have taken a picture of mine but I didn't before i left the house for work and right off the start i see two things that are wrong. I am sure there are a bunch of minor issues but I know that these two things are supposed to be pretty standard issues. I think it has to do with exposure settings.

The tip of the space needle is missing and the inner most row of the pin lines it all warped and curled up. Before I run another test are these issues caused by under or over exposure. I am using Elegoo Grey. I printed using the test print in the Resin XP finder folder so 50u 8x80 and 15. the 8x80 is way too much. The bottom layers are stuck like glue lol. I am going to drop that to 70. The test strip looked like 12 sec but I didn't adjust the print (I know) so if this is a typical sign of overexposure I know I can drop it to 12 and see. I assume it is.

翻譯年糕

Andrius AmeraLabs
2019-03-01 21:11:24

Andrius AmeraLabs
2019-03-01 21:12:24

Dustin Skye
2019-03-01 21:58:06

Dani Rose
2019-03-01 22:00:53

Dustin Skye
2019-03-01 22:02:16

Dani Rose
2019-03-01 22:10:58

Dustin Skye
2019-03-01 22:14:26

Chris D'Andrea
2019-03-01 22:38:38

Dustin Skye
2019-03-01 22:39:13

Fred Breton
2019-03-01 23:46:07

Sen Kun
2019-03-02 05:11:13

Joel Ligeiro
2019-03-02 19:39:31

Chris D'Andrea
2019-03-02 21:01:08

Mantas Aus
2019-03-04 07:20:09

原文網址 Nicolai Flemming
2019-03-01 19:57:14

I'm having issues with layers separating at 2mm. It happens everytime but is especially visible when printing small parts. Anybody got any idea why this is happening? I'm using Harzlabs Model Cherry resin with 90s on the bottom layers, 17s exposure and 1s off time.

翻譯年糕

Dennis Tomson
2019-03-01 23:36:54

Dennis Tomson
2019-03-01 23:37:34

Nicolai Flemming
2019-03-02 03:32:09

Dennis Tomson
2019-03-02 16:25:21

原文網址 Nadine Krebs-Vuilleumier
2019-03-01 19:44:00

What Setting have I to use for flex resine like monocure 3d flex 100?thanks

翻譯年糕

Christian Plösser
2019-03-01 19:54:56

原文網址 Daniel Kollar
2019-03-01 19:22:36

Hi guys I have few questions.
I left my dirty IPA under UV light with an idea to clean it and i thought that it will cure resin and it became white like this. Obviously it was quiet stupid from me.Any idea why did this happened?
Can I use methylated spirit instead of IPA?
Can I use white spirits instead of IPA?
Thanks for answers!

翻譯年糕