Anycubic Photon Printer Owners 造訪社團

原文網址 Richard Wilson
2019-02-18 03:59:59

It turned out OK, but there are a lot of layer lines, quite like an FDM printer. But not displeasing. I’d love to know how to keep the green transparent, or at least glossy. It does go full after a while ? but for this model I am happy, project closed

翻譯年糕

Ron Luttrull
2019-02-18 04:59:48

原文網址 Marcin Lekston
2019-02-18 02:36:08

Hi I changed fep film and get prints like this
You think it's too loose?
Edit: I check fep it's OK again print like this
Can it by by wobble. Of z. Axis?

翻譯年糕

Chad Elstad
2019-02-18 02:39:10

Marcin Lekston
2019-02-18 02:41:02

Chad Elstad
2019-02-18 02:46:32

Vinicius Silva
2019-02-18 02:47:06

Michael Supraholic
2019-02-18 03:05:07

Vinicius Silva
2019-02-18 03:11:32

Michael Supraholic
2019-02-18 03:12:47

Michael Supraholic
2019-02-18 03:18:31

Kevin Hull
2019-02-18 11:26:22

Luis Fernando Corado
2019-02-18 11:55:44

Michael Supraholic
2019-02-18 17:10:04

Marcin Lekston
2019-02-19 02:43:56

原文網址 Chadwick Foster Maerz
2019-02-18 02:12:06

my first print with the photon. and my encloser for the printer and filter set up.

翻譯年糕

Chadwick Foster Maerz
2019-02-18 04:31:12

Bard Vanhammer
2019-02-19 00:37:38

Jarrod Smith
2019-02-19 02:55:52

Matt Hilton
2019-02-19 09:26:02

Garret Bertrand
2019-02-21 00:50:42

原文網址 Will Mckay
2019-02-18 00:39:16

Love the photon. I just modelled printed and painted this. The quality was better than a $60 equivalent from Forgeworld. :) Win!

Printed at 0.04mm with transparent green

翻譯年糕

Sebastian Hofi
2019-02-18 00:47:16

Adam Green
2019-02-18 01:01:13

Tom Leech
2019-02-18 01:13:57

Jim Leenan
2019-02-18 01:25:33

Jason Odegard
2019-02-18 01:32:08

Christopher Ashworth
2019-02-18 01:42:32

Garret Bertrand
2019-02-18 01:48:23

Paul Bansard Greveson
2019-02-18 01:49:18

Elbert van Leeuwen
2019-02-18 01:51:53

Ryan Gamble
2019-02-18 01:52:08

Connor DjGlargum Whitesell
2019-02-18 02:11:48

Will Mckay
2019-02-18 02:17:11

Tom Brick
2019-02-18 02:35:22

Sean Pollman
2019-02-18 03:31:52

Rienov Hardspinn
2019-02-18 13:48:44

Six Hatch
2019-02-18 15:14:04

Eric Kemble
2019-02-19 11:43:29

Will Mckay
2019-02-19 19:28:46

Eric Kemble
2019-02-20 11:50:52

原文網址 Shayne Webb
2019-02-18 00:33:24

Are there any resins that are food-safe?

翻譯年糕

Robert Silvers
2019-02-18 00:34:38

Shayne Webb
2019-02-18 00:50:57

Robert Silvers
2019-02-18 00:52:24

原文網址 Michael M Thompson
2019-02-18 00:23:12

Loving this printer. The boat is my version if the Bridge Erection Boat manufacturer by Birdon.

翻譯年糕

原文網址 Mike Foreman
2019-02-18 00:15:23

So I printed my first minis vertically on their base. Seem people angle them 45deg on their back. Which is best?

翻譯年糕

Douglas Guerra Dos Santos
2019-02-18 00:23:40

Alex Vee
2019-02-18 00:54:03

Robert Anhalt
2019-02-18 00:58:32

Joschka Röben
2019-02-18 01:28:27

Mike Foreman
2019-02-18 02:06:51

Mark Wardle
2019-02-18 11:15:48

Dexter WG
2019-02-18 13:03:24

Benny Woolley
2019-02-18 19:41:44

Mike Foreman
2019-02-18 21:26:26

Benny Woolley
2019-02-18 21:35:02

原文網址 Janosch Simon
2019-02-18 00:02:02

https://www.youtube.com/watch?v=v3N_9-YLa6g
wohoo second cast kind of succsess with my 1978 Heraeus CL-G :D Resin was from Bluecast X10 anycubic Photon