Anycubic Photon Printer Owners 造訪社團

原文網址 Nick Wright
2018-12-02 13:26:39

Is there anyway to only generate really short supports?
I often print relatively small models and the min support height of 3.5 mm often takes 20-30% of the entire print time. If I could reduce this height down to 1-1.5mm I could cut 10-15mins off my prints.
So is it possible to set the min support height below 3.5mm?

翻譯年糕

Sen Kun
2018-12-02 13:31:05

Nick Wright
2018-12-02 13:34:10

原文網址 Valas Darkholme
2018-12-02 10:02:11

Can you help a guy out by chance? My first print failed.

I went to print a free pikachu and some slime rancher slimes from thingiverse.

The two big slimes were fused to the reservoir with big chunks missing from their tops, and it looks like I only got a couple of layers, in the middle, for the 3 little pikachus I tried to print, and they were also fused to the reservoir.

The two little slimes were fused to the print bed / came out fine.

Free Thingiverse models, rescaled in mesh lab, loaded into the stock Anycubic photon slicer with default settings.

I leveled my photon based on what the book said, and used the included resin.

What would cause this type of failure?

翻譯年糕

Stefan Giudici
2018-12-02 10:50:45

Valas Darkholme
2018-12-02 11:10:31

Adam Widdowson
2018-12-02 11:20:55

Valas Darkholme
2018-12-02 15:17:56

Alex Butler
2018-12-05 05:53:00

Valas Darkholme
2018-12-05 06:20:43

Alex Butler
2018-12-05 10:14:18

Valas Darkholme
2018-12-05 10:18:10

Paul Jacobs
2018-12-05 10:36:31

Paul Jacobs
2018-12-05 10:37:42

Paul Jacobs
2018-12-05 10:40:08

Valas Darkholme
2018-12-05 10:54:00

Valas Darkholme
2018-12-05 10:54:43

原文網址 Luca Agnelli
2018-12-02 09:34:13

hello guys, I ask you, after you can find the best parts of the Proton. hello guys, I ask you, after you can find the best parts of the Proton. 翻譯年糕

原文網址 Eduardo Fonseca Rodrigues
2018-12-02 09:14:58

Hello guys. I have been able to solve the above problems, and I can already make prints. Thanks for your help. However, I have had this error recently. Is it the pendrive I'm using that is broken?

翻譯年糕

Trea Cotton
2018-12-03 02:08:29

Eduardo Fonseca Rodrigues
2018-12-03 05:22:11

原文網址 Brayden Funk
2018-12-02 07:49:34

Finally have my printer up and running. Everything is coming out great. Anyone have any really cool D&D style miniatures that are free? Looking for stuff like the super detailed basilisk on thingiverse, or really anything that's that good looking.

翻譯年糕

Simon Powell
2018-12-02 08:07:42

Steven Tooze
2018-12-02 08:38:39

Philippe Maegerman
2018-12-02 21:42:19

原文網址 Christopher Botha
2018-12-02 07:20:30

If you are using Chitubox and want to create a video of the frames. there are a few options around but all are messy or require spyware ridden "free" video editors, so i wrote one for myself quickly.

for c# devs the code is in first comment. read the Using's to see what has to be included in VS, code is c#, dirty AF , but, it works. alter the X,Y and compression ratio and framerate speed as required.

翻譯年糕

Christopher Botha
2018-12-02 07:21:55

Ruslan Konovalov
2018-12-02 13:23:52

Sen Kun
2018-12-02 17:50:08

Nicolas Poussin
2018-12-02 19:30:51

Christopher Botha
2018-12-03 02:25:45

原文網址 Takeo Kurita
2018-12-02 06:57:56

Hi, I'm quite new to 3d printing with resin and got a few questions:

1. After cleaning a printed part with IPA and water, is it still toxic until it is fully cured with UV- or sun light?

2. What UV lights could you recommend? Is there a good video out there that has a recommendation how to build a UV curing chamber?

3. The build volume in the photon slicer settings are a bit different from what the printer specifications say. 68.04 x 120.96 x 150 compared to 65 x 115 x 155. Are the settings correct or should they be changed?

翻譯年糕

James Cachia-Garrett
2018-12-02 07:13:09