[ 三則重要公告 Important Announcements ]
[ 重要公告 1 ]
收到熱床的朋友們如果發現組好後熱床無法升溫，問題可能在這裡：由於我們的疏忽，說明書上 D03 步驟的熱床電源線標錯位置。原本應該接到 V+ 的線誤植為 V- ，請照著新的說明書勘誤表重新接該端子即可！如果改接後仍然遇到問題請洽 support@atom3dp.com 感恩！
[ 重要公告 2 ]
裝熱床的 2.0 朋友們請務必更新到最新的韌體 2.0.7 以便改善自動校正。可以至
http://www.atom3dp.com/wp-conte…/uploads/…/07/ATOM-2.0.7.zip
下載。
[ 重要公告 3 ]
少數的斷熱板上的 Φ5mm 孔洞因為烤漆的關係直徑變小導致玻璃挾持器的 M5 螺絲比較難穿過，可以採取以下的方式處理：
1. 用 5mm 電鑽鑽一下讓 M5 螺絲可以順暢通過，這動作並不會影響玻璃挾持器的運作。
2. 手邊沒有電鑽或其他工具的用戶，麻煩跟我們連絡，提供您的姓名、收件
地址與電話。請您先將舊的斷熱版包裝好，快遞會先送上新的斷熱版後，取走舊的版本。
今後出貨的斷熱板我們會確保孔徑是理想尺寸，請不用擔心。
[ Important Announcements 1 ]
If your heatbed is not responding to the heat up command, the problem could be its misconnections to the power supply. Due to an error in the instruction manual on section D03, the main cable for the heating disc is shown to be connected to the wrong port. The correct port is V+, please make the adjustments according to the revision instruction below. Should you have further question please let us know at support@atom3dp.com
[ Important Announcements 2 ]
Please remember to update to the latest firmware 2.0.7 which can be downloaded here:
http://www.atom3dp.com/wp-conte…/uploads/…/07/ATOM-2.0.7.zip
[ Important Announcements 3 ]
In some cases the Φ5mm holes on the heat shield could be blocked by the coating, making it difficult for the M5 screw to pass. Please use an electric drill with a 5mm drill bit to remove the excess coating allowing the screw to pass smoothly.
Thank you!
廖新弘
2016-07-07 10:27:25
Shelly Kuo
2016-07-07 10:31:48
廖新弘
2016-07-07 10:31:51
陳明谷
2016-07-07 10:47:38
Lawrence Lee
2016-07-07 17:10:16
廖新弘
2016-07-07 18:00:41
H-m Lin
2016-07-11 19:11:42
想請問一下~舊版熱床的更新件~預計何時會出貨~沒有明確時間嗎??
Morgan Chang
2016-07-12 20:06:23
我也在等修正套件，不知何時出貨呢？
舊版熱床掛掉一個多月了:-(
KioSky Chung
2016-08-03 20:07:15
我的2.0是嘖嘖預購的
從沒收到熱床套件
請問這是需要額外加購的模組嗎？網站上好像沒在賣？謝謝
