ATOM 3D Printer Group 造訪社團

有體重限制的港覺

填充直上100%!!!!!

軟料侍候！

覺得軟料只能在腳板位置上而已

请问能承受多少kg？

打印方向抓對,FILL100%,肯定足夠!

樓上掛保證 有裝況請找大大理賠XD

圖畫一畫，印出來，走走看就知

拆件列印中

太勇了，翹了繼續印

哇，印鞋子也，太讚了吧

開放模型檔 大家來挑戰吧

謝謝大家的討論，最後的幾公分居然炒米粉了哈哈哈哈

不完美 也是一種美

完成了 但太大雙 哈哈哈

再縮小一點呢？

測不準;p

是的！！！ 熱收縮而已...

你的應該有一點問題，我之前也這樣。

我之前是上升的螺桿是歪的，所以每轉一圈就會偏一點，就照成您這樣規則狀的紋路。

這不是很正常嗎?

說明書 有寫 很正常

我印出來也是這樣~

恭喜你，進入另外一個世界了

應該正常

用垃圾袋保溫罩效果還是不好

可能要動用加溫設備，可是馬達跟機板撐得住嗎？

有熱床就開阿...

沒熱床，原廠沒得買，買副場嗎?

ABS ?

恩，abs,

那就認命裝熱床吧...不然 問
戴士偉 這種無熱床印不印的出來 ;p

下一步要設計灑水系統，這樣成品耐不住水壓

要耐水壓....
hmmm....
印完浸泡個pu膠還啥

完全工程上使用

李大，可以告知耐高溫的pla何處購買？

poni_greentek露天上有看到

溫度設定多高?

i am just a bit skeptical on how many english speaking users are there with Atom 2.0, but it's definitely helpful to hv a group for that. Please let us know on this group when u form a new one.

There may not be many users but the ones out there do need help at times and we shouldnt be isolated due to the limited numbers of people! we spent the money to use this product just as you have so a group that can share ideas easier is only benifiting Atom as a company

I remeber there's a ATOM 2.0 international club for english speakers, perhaps you should ask admin

Sounds great for create a English group.
Actually, I'm customer support engineer.
if u create that group, plz let me know...

i think that just a fanpage not a group....

If there is an English group, I would like to be in there as well. :_)

Po Ting Liu said that there is a english speaking group. I wonder where to find it?!

An English language discussion board has been set up prior to Atom initializing its expansion to the US market. The bard uses the Slack software https://slack.com/downloads and right now has only a very few members and no significant content. The moderator is in the US now and will hopefully be ready to add new members soon.

Mike Galvez

Well i keep hearing about an Atom international fb group but havent found it during a search! I am having major issues with my printer and since there is little to no customer service support from Atom to fix printer issues i will just have to create a fb page and hope i can resolve my isseus on my own!

I had problems and solved them all. Whats the problem? ?

just try ask and take photo for your issues on this FB group. someone will help u. no worry.

The new English group should be announced on Monday. In the meantime post your issues here and help will arrive.

after the auto leveling process ends the hot end instead of printing drops down directly into the glass so hard it pops the arms off

Most of my issues I've solved through Birk Binnard, one other friend, and Google .

But yea, I see so many posts and wonder, "what are they talking about and would it help me?"

Wait, so at the end of the auto level it goes back down into the glass or it goes down into the glass when you try to print?

What would be nice is Atom having some sort of customer support for the product they sell!

Bryan - the Atom folks are aware of the need for customer support in the US. There should be some news about this starting next week.

About your problem: If the printer completes the Auto Level procedure correctly, meaning it senses the print bed at e ach location and then returns to a center position when done, the problem you described sounds like bad GCode. "Bad" means GCode generated by a slicer that is tailored for a particular printer that has geometry and/or control circuits different from the Atom2.

Can you post the first 20 lines or so of the GCode you tried to print? It will look something like this:

; GCode generated by CraftWare

G28 ;Home
;G0 F2400 E-5.0000 <===== Comment this

M109 S190 ;set head temp (wait)
; ------------------------------------
; Layer #0
; ------------------------------------
G21 ; mm
G90 ; abs
G92 E0 ; reset extr
M106 S0
;segType:Skirt
;G0 F2400 E-5.0000
G0 F3300 Z0.200
G0 X-52.398 Y51.575 F4500
G0 F2400 E0.0000

This is GCode I recently created with the Craftware slicer. It generates a line of code that the Atom2 does not like, so I commented it out - see the last line that starts with a ; character - this is the special character that causes the printer to ignore everything on that line following the ;.

My guess is your GCode will have some command that causes your printer to try to reach a position outside it's limits. Doing this is not good - you risk breaking a timing belt, gouging your print bed, or throwing off the geometry of the printhead frame.

https://m.facebook.com/atom3deurope/
We have already created a page for ATOM in English for the same reason, we need information I English as we don't understand traditional Chinese. We are official distributors in Spain and we sent a message to the ot her official distributors I order message the page but we didn't get any answer. The page is already created and I invite you all to like our and start sharing things about the printer and printings in English.thank you, we really believe is really necessary because our customers can use it also. Thank for share

USB也會供電呀！！！
就是等噴頭降到100內，就可以斷電惹！！！

印的時候最好不要接USB，不然有可能因為USB電壓波動而突然停止列印

喔喔了解，一直以為我哪裡裝錯了還拆開來檢查...謝謝各位!

那可以再問一個菜問題嗎，不想印了中途想取消列印>>關機要怎麼按@@?

記得選單裡面有一項是STOP and Home的，找一下

Ok!

好美的玻璃面

感覺沒塗膠，直接上，沒問題嗎？

噴嘴冷卻後我都會習慣再按一次disable stepper才會關機，避免有時候是非正常列印程序的時候沒有自動關閉馬達，不知道有沒有必要

你高興怎樣關就怎樣關 壞了在休就好