• 3D列印服務
  • #maker+t=market
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Chris Warkocki
2019-03-20 05:12:38

I will be posting a lot of info on this combo. I will say after unboxing no other SLA printer I've tried has been this well built. It's a tank of a machine and weighs about 30lbs.

It's sad that my photon died last month as I won't have side by side but I'll try and get it going again asap.

翻譯年糕

Rob Klingberg
2019-03-20 05:27:15

Mitchell Cooper
2019-03-20 05:28:25

Peter Teal
2019-03-20 05:31:57

James Anderton
2019-03-20 05:34:51

Vedran Marjanovic Wekster
2019-03-20 05:42:09

Vedran Marjanovic Wekster
2019-03-20 05:42:47

Hobby Mike
2019-03-20 05:45:33

John Alvarado
2019-03-20 05:59:58

Timothy Purcell
2019-03-20 06:01:27

Darren Tarbard
2019-03-20 06:09:27

Fred Breton
2019-03-20 06:20:11

Fred Breton
2019-03-20 06:20:51

Guti Gutmann
2019-03-20 06:21:19

Fred Breton
2019-03-20 06:23:07

Nicolas Poussin
2019-03-20 07:40:24

張辰謙
2019-03-20 08:06:01

Jordan Geml
2019-03-20 08:33:22

Andrew Gott
2019-03-20 08:44:34

Tony Luong
2019-03-20 09:20:01

Robert Silvers
2019-03-20 11:11:06

Mike Eckert
2019-03-20 12:22:48

Robert Silvers
2019-03-20 12:28:35

Chris Warkocki
2019-03-20 13:13:50

Robert Silvers
2019-03-20 13:15:41

Chris Warkocki
2019-03-20 13:19:21

Robert Silvers
2019-03-20 13:24:00

Curt Pangracs
2019-03-20 13:31:10

Robert Silvers
2019-03-20 13:36:42

Curt Pangracs
2019-03-20 14:01:46

Chris Warkocki
2019-03-20 14:17:23

Fred Breton
2019-03-20 14:26:35

Curt Pangracs
2019-03-20 14:32:53

Simon Krause
2019-03-20 15:58:42

Gerald Fernando
2019-03-20 18:56:02

Kyle Van Patten
2019-03-20 20:30:59

Chris Warkocki
2019-03-20 21:54:51

Chris Warkocki
2019-03-20 21:55:51

Chris Warkocki
2019-03-20 22:01:44

Che Fielding
2019-03-20 22:13:47

Chris Warkocki
2019-03-20 22:20:55

Mike Roof
2019-03-20 22:55:38

Chris Warkocki
2019-03-20 23:04:17

Keith Barnett
2019-03-20 23:05:46

Chris Warkocki
2019-03-20 23:24:21

Chris Warkocki
2019-03-20 23:27:21

Fred Breton
2019-03-21 01:26:21

Fred Breton
2019-03-21 01:26:52

Chris Warkocki
2019-03-21 01:27:00

Fred Breton
2019-03-21 01:27:24

Fred Breton
2019-03-21 01:28:44

Chris Warkocki
2019-03-21 01:30:00

Fred Breton
2019-03-21 01:33:41

Chris Warkocki
2019-03-21 01:34:48

Fred Breton
2019-03-21 01:37:34

Chris Warkocki
2019-03-21 01:39:11

Fred Breton
2019-03-21 01:42:38

Chris Warkocki
2019-03-21 01:44:23

Mike Roof
2019-03-21 12:50:28

Chris Warkocki
2019-03-21 12:54:52

Gerald Fernando
2019-03-21 12:54:59

Gerald Fernando
2019-03-21 12:55:36


原文網址 Chris Warkocki
2018-05-10 00:12:33

Didn't even think stuff like this was possible. Just need a good sanding and some primer and this guy can go to its new home.

Wanhao grey at 0.40mm layer heights.

Much thanks to some helpful a humans in the group. Haven't had to relevel the bed since and as a bonus it's printed perfect since.

翻譯年糕


原文網址 Chris Warkocki
2018-05-06 22:23:45

Hello!

Finally got my photon last week and it's been printing great minus a consistent issue with anything I do in meshmixer.

I'm printing d&d minis and I'll consistently loose the back end of the figures base. Even with a ton of additional manual supports added the crazy things just won't hold on.

I seem to only get this issue printing at 0.05mm layer heights and when printing at 45 model orientation. I'm fine if the model is flat to the build plate.

I've triple checked my z height and the paper has good grip and I've tried looser and tighter with results being the same.

I've tried upping exposure time by 1 second as well.

Any thoughts? If I can get some consistent hood from the supports I'll be a happy friggin camper and can start printing without babysitting as much.

Appreciate the help in advance.

翻譯年糕


 

討論主題

全不選 常用關鍵字