Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Ian Hawkins
2020-01-27 04:17:49

Ok people, what could have caused this to go wrong?

I printed this STL out last week without problems, decided to reprint at 0.02 rather than 0.04 to try and smooth it out a little and after 12 hours I came back to this.

翻譯年糕

Neil Castle
2020-01-27 04:19:45

Michael Mathews
2020-01-27 04:21:01

Ian Hawkins
2020-01-27 04:21:19

Étienne Dré Landry
2020-01-27 04:30:51

Ryan Tudor
2020-01-27 05:14:06

原文網址 Ian Hawkins
2019-07-28 22:57:22

I'm almost out of the green resin I got with my printer, and looking for options.

I usually print 28mm minis and stuff for gaming, I've found the green great for detail but it shatters really easily which isn't great for things that will be handled a lot as gaming pieces.

What's the best resin for miniatures that has a little flex in it but still holds the detail?

翻譯年糕

Zena Andreou
2019-07-28 23:02:22

Bob Deblier
2019-07-28 23:04:27

Spike Walker
2019-07-29 00:00:47

Clint Primley
2019-07-29 00:59:23

Spike Walker
2019-07-29 00:59:53

Paul West
2019-07-29 20:52:20

Thomas Wright
2019-07-30 09:45:31

原文網址 Ian Hawkins
2019-03-01 01:16:49

After a failed print how do you clean the cured resin off the fep? Tried chiping it off but put a hole thought the film yesterday. Just had another failure and dont want to ruin another one

翻譯年糕

Victor Sanders
2019-03-01 01:17:27

Simon Powell
2019-03-01 01:17:55

Tori Beckett
2019-03-01 01:19:01

Derek Reihe
2019-03-01 01:19:26

Piotr Felke
2019-03-01 01:20:21

James Hendrix
2019-03-01 01:21:22

Matthieu Mouron
2019-03-01 01:22:13

Jannick Langfahl
2019-03-01 02:05:34

Mark Wardle
2019-03-01 03:01:01

Travis Hunt
2019-03-01 03:02:50

Orwin SantaCruz
2019-03-01 03:49:59

Chris D'Andrea
2019-03-01 03:53:01

JJ Lee
2019-03-01 04:12:25

Colin Graham
2019-03-01 05:06:03

Ian Hawkins
2019-03-01 05:30:04

Daniel Worden
2019-03-01 11:42:56

Michael Zinski
2019-03-03 12:05:59

Daniel Worden
2019-03-03 19:08:54

Daniel Worden
2019-03-03 19:09:20

Joao Fernando Fonseca
2019-03-03 21:20:38

原文網址 Ian Hawkins
2018-11-18 18:03:38

Just ordered a photon on an Amazon deal, Looking for recommendations for uv curing equipment. I've seen some mention of nail polish curing lamps, are these tall enough? I'll likely be printing 28mm gaming stuff off.

翻譯年糕

Mark Niesche
2018-11-18 18:06:01