Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Matt Goldrick
2019-08-19 01:19:52

So I haven't used the printer in almost 4 months (no projects needed for the job), but now i've loaded up a couple of small prints and i can't get anything to stick to the bed. I've tightened the FEP, reveled everything and I've included my settings below. I've done 4 tries so far and nothing is sticking. Any help would be appreciated.

翻譯年糕

Chad Elstad
2019-08-19 01:34:28

Matt Goldrick
2019-08-19 01:35:30

Niklas Rosenkilde
2019-08-19 01:36:45

Matt Goldrick
2019-08-19 01:37:41

Chad Elstad
2019-08-19 01:37:54

Matt Goldrick
2019-08-19 01:38:23

Eric Garcia
2019-08-19 01:39:14

Paul Tyer
2019-08-19 01:42:05

Matt Goldrick
2019-08-19 01:46:02

Matt Goldrick
2019-08-19 01:51:31

Paul Tyer
2019-08-19 04:09:53

Clifford Schwankner
2019-08-19 04:34:13

Matt Goldrick
2019-08-19 04:57:01

Roque Gallas Junior
2019-08-19 05:51:27

Matt Goldrick
2019-08-19 05:52:37

Matt Goldrick
2019-08-19 05:52:44

Clifford Schwankner
2019-08-19 05:54:59

Matt Goldrick
2019-08-19 06:00:00

Baptiste Arnault
2019-08-19 06:23:05

Clifford Schwankner
2019-08-19 06:24:52

Valas Darkholme
2019-08-19 06:29:15

原文網址 Matt Goldrick
2019-02-19 14:47:07

Lost my first FEP tonight. ? who’s got a good reference for how to replace it? I’ve got new film on the way from amazon and I understand the basics of it. But any tips? Tricks?

翻譯年糕

John Rodriguez
2019-02-19 14:51:09

Adam De La Bête
2019-02-19 14:55:45

Mark Wardle
2019-02-19 14:57:09

Carlos Villamar
2019-02-19 15:00:17

Sen Kun
2019-02-19 15:25:00

Graham Leek
2019-02-19 15:55:44

Chad Elstad
2019-02-19 22:26:06

Mike Johnson
2019-02-19 22:47:26

Barry Masterson
2019-02-19 22:54:38

Matt Goldrick
2019-02-19 23:13:47

Garret Bertrand
2019-02-19 23:53:01

Jarrod Smith
2019-02-20 00:09:42

Richard Shapiro
2019-02-20 09:44:03

Garret Bertrand
2019-02-20 10:43:36

Mark Wardle
2019-02-20 10:44:15

Mark Wardle
2019-02-20 10:45:35

Mark Wardle
2019-02-20 10:46:15

原文網址 Matt Goldrick
2019-01-15 23:32:54

So the printer printed all the supports but not the actual miniature itself. Well it did print it, it was just stuck to the FEP. Any settings I should adjust in the printer? Or is this something I should adjust in the slicer with the supports?

翻譯年糕