Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Keenan Beblo
2019-09-12 08:54:00

What support settings do you guys like? I’m just curious to know what everyone is using!

翻譯年糕

Melecio Guzman
2019-09-14 02:46:03

Danny Broekhuis
2019-09-14 02:50:44

原文網址 Keenan Beblo
2019-07-29 06:18:24

Well that was a waste haha. No only did the bottom layer peel up but I ran out of resin part way!

翻譯年糕

原文網址 Keenan Beblo
2019-06-08 23:41:30

How can I help models not come off supports during printing?

翻譯年糕

Ty Mansfield
2019-06-08 23:46:23

陳小鎬
2019-06-08 23:47:52

Bob Deblier
2019-06-08 23:48:26

Rob Mayberry
2019-06-08 23:50:07

Keenan Beblo
2019-06-09 00:08:26

John Goodrich
2019-06-09 01:34:47

Chad Elstad
2019-06-10 22:59:41

Ty Mansfield
2019-06-10 23:33:29

原文網址 Keenan Beblo
2019-06-01 11:32:58

Just curious, is there a better tool to get the tension on the FEP or just a 12mm bottle cap

翻譯年糕

Chris Comeau
2019-06-01 11:36:18

Chris Comeau
2019-06-01 11:40:14

原文網址 Keenan Beblo
2019-05-26 21:40:04

Recommendations on which replacement FEP film to get in canada?

翻譯年糕

原文網址 Keenan Beblo
2019-04-20 12:56:55

Two questions. What are the layer heights I can reasonably print at? Say X -> 0.1 secondly if I want to print at finer layer heights should I reduce exposure time if I’m coming from 0.05? Or is it ok to leave it as is?

翻譯年糕

Adam Horton
2019-04-20 13:11:35

Keenan Beblo
2019-04-20 13:18:13

Danny Lloyd
2019-04-20 19:41:23

Richard Shapiro
2019-04-20 22:43:06

原文網址 Keenan Beblo
2019-04-19 08:04:19

My Photon rescued my Prusa MK3S today! Unfortunately the Anycubic green was too see through and had to use their blue. But issue resolved ?

翻譯年糕

原文網址 Keenan Beblo
2019-04-12 10:31:38

Left the IPA bucket out by accident and the sun got to it...oh well lesson learned!

翻譯年糕

Dave Smith
2019-04-12 10:38:12

Calvin Tan
2019-04-12 10:45:40

Travis Hunt
2019-04-12 11:10:02

Eric Wilfreesboro
2019-04-12 11:13:54

Muhammad Zulkhairol Yacob
2019-04-12 12:10:00

Tom Howley
2019-04-12 13:24:49

Xavier Cebeira
2019-04-12 20:18:19

John VanRyn
2019-04-12 20:25:42

Richard Shapiro
2019-04-12 21:49:22

Francisco Angelini
2019-04-12 22:56:10

Alwin Chan
2019-04-12 23:00:55

Kevin McGuigan
2019-04-12 23:35:06

Ed Wilson
2019-04-12 23:48:27

Dániel Vœlkel
2019-04-13 01:09:11

Amy Baldwin
2019-04-13 03:02:31

Dominick Trascritti
2019-04-13 03:39:39

Matt Leese
2019-04-13 03:46:05

Amy Baldwin
2019-04-13 04:00:14

Amy Baldwin
2019-04-13 04:00:47

Dominick Trascritti
2019-04-13 04:38:02

Chad Elstad
2019-04-13 05:00:52

David Nicholls
2019-04-15 02:49:07

原文網址 Keenan Beblo
2019-04-08 13:22:51

Hopefully my drain hole works ?

翻譯年糕

Jordan Geml
2019-04-08 13:27:53

Stefan Giudici
2019-04-08 13:40:09

Andrew McKay
2019-04-11 03:18:25

原文網址 Keenan Beblo
2019-04-02 06:01:16

*** solved. I’m just crazy and thought I swapped settings to my “green” settings...but didn’t. Leaving this up for anyone else ***

well thats an interesting fail I have not run into. thoughts? seems to have fused the section that is supposed to be a coil and I have 1-2 layers of just flat cured resin

any cubic green
.5 layers
5 bottom
16 exposure time
60 for the bottom layers

翻譯年糕