Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Sami Ahmari
2019-10-05 01:42:03

I am having problem with photocenteric flexable black resin, only base layer gets stick to build plate. I increased exposure time up to 50 sec but no luck. 8 Base layers with 120 seconds 50 microns layers with 40 20 to 50 seconds exposure time. Anybody had success with this resin?

翻譯年糕

原文網址 Sami Ahmari
2019-06-06 07:41:54

I am looking for recommendations for silicon rubber like end results to print some o-ring type parts for waterproofing. Any suggestions?

翻譯年糕

Nick Neal
2019-06-06 08:38:28

Sami Ahmari
2019-06-06 08:52:47

原文網址 Sami Ahmari
2019-05-07 10:12:44

I have been using Siraya blu for functional mechanical parts wondering if there is even better tough resin with more abs characteristics. Blu is fine but still little brittle and not good for high temperature

翻譯年糕

Sean O'Hayer
2019-05-07 10:25:02

Sami Ahmari
2019-05-07 10:27:03

Stefan Giudici
2019-05-07 12:54:15

Richard Burrell
2019-05-11 21:40:12

原文網址 Sami Ahmari
2019-04-25 02:17:27

Any idea why this could happen?
I’ve got wrapping at those points
Which supports also detached or never attached for some reason

翻譯年糕

Tom Franco
2019-04-25 02:18:55

Zena Andreou
2019-04-25 02:42:34

Sami Ahmari
2019-04-25 02:47:18

Zena Andreou
2019-04-25 03:02:34

Sami Ahmari
2019-04-25 03:03:12

Bob Deblier
2019-04-25 03:16:28

原文網址 Sami Ahmari
2019-04-07 03:45:50

I am really disappointed with photon accuracy. I find .2 to 0.8 mm error in all x,y and z axis, even before curing. I tried 2 different resins, different exposure timing, two different slicer software, and even tried different orientations for the same object! 3dhubs.com SLA prints was always accurate I wondering if it is a common error in DLP's or it is just my photon.

翻譯年糕

Juan Camilo Herrera
2019-04-07 03:49:27

Ed Wilson
2019-04-07 03:51:10

Ed Wilson
2019-04-07 03:51:53

Ray Routledge
2019-04-07 04:22:32

Sami Ahmari
2019-04-07 04:24:17

Ray Routledge
2019-04-07 04:27:16

Blake Moody
2019-04-07 04:27:42

Sami Ahmari
2019-04-07 04:28:26

Blake Moody
2019-04-07 04:29:00

Sami Ahmari
2019-04-07 04:30:50

Blake Moody
2019-04-07 05:11:34

Adam Foster
2019-04-08 01:05:25

Vinicius Silva
2019-04-09 18:49:57

原文網址 Sami Ahmari
2019-04-05 12:49:12

Any idea what is the cause? I printed the red part with my older 3d printer. As you can see in the photos grey part printed with photon is off about 0.5mm in Z axis. This is very consistent in my last couple of tests. Sliced with anycubic slicer 1.3.3.

翻譯年糕