Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Stephan Hillman
2019-07-20 12:30:02

This took a while, but I learned a lot.

翻譯年糕

Joseph Covington
2019-07-20 14:00:49

Stephan Hillman
2019-07-20 20:35:55

原文網址 Stephan Hillman
2019-07-01 01:05:47

Where do you buy your replacement FEPs? I think the standard thickness on Anycubic's FEPs is 0.15mm. Do you use that or recommend anything else?

翻譯年糕

Michael J Morris
2019-07-01 01:07:00

Rob Mayberry
2019-07-01 01:10:06

伟洪
2019-07-01 10:30:42

Michael J Morris
2019-07-01 12:04:39

伟洪
2019-07-01 12:11:36

Michael J Morris
2019-07-01 12:17:17

原文網址 Stephan Hillman
2019-06-20 00:57:02

So, after many successes with my Photon since buying it a month ago, I've been running into problems with this one print. My first attempts were made with ChiTuBox with standard support settings and Heavy supports. Portions of the model printed fine, but portions pulled away from the supports such that there was a gap between the tip of the support and the base of the model. I increased the density of supports and adjusted the angle until there was no more red showing on the underside of the model. That started ok, but at some point, all of the support bases pulled away from the actual print plate.

Am I having multiple independent issues or is this traceable to one thing I'm doing wrong. As I said, I've had lots of successful prints and managed to fix the other problems I've run into with minimal effort. I just can't get this one print figured out.

翻譯年糕

Zena Andreou
2019-06-20 01:02:28

Stephan Hillman
2019-06-20 03:50:54

Stephan Hillman
2019-06-21 20:17:31

原文網址 Stephan Hillman
2019-06-15 00:32:28

I'm sure this is out there somewhere, but does anyone have the recommended supports settings for ChiTuBox? I was using the default settings, but the auto support function was putting in so many supports that just cleaning them off was a hassle and they left a ton of dimples on the model at the support touch points. Thanks!

翻譯年糕

Bob Deblier
2019-06-15 00:37:22

Stephan Hillman
2019-06-15 00:38:03

Jeff Wand
2019-06-15 00:40:14

Justin Bullock
2019-06-15 00:42:40

Myrobot Stuff
2019-06-15 03:13:32

Justin Bullock
2019-06-15 03:15:40

Gary Houser
2019-06-15 03:41:58

Shane Johnson
2019-06-15 03:47:09

Justin Bullock
2019-06-15 03:52:36

原文網址 Stephan Hillman
2019-06-03 02:57:33

Not sure if you can see on the pic, but I’ve got these glossy areas on the print that I’m not sure what to do with. I’ve cured the model and washed it, but this still looks like uncured resin. Any suggestions?

翻譯年糕

Francesco Ostili
2019-06-03 02:59:34

Jake Bradbury
2019-06-03 03:02:24

Stephan Hillman
2019-06-03 03:13:02

John Russell
2019-06-03 03:22:00

John Russell
2019-06-03 03:22:54

Tom Logan
2019-06-03 03:32:59

Stephan Hillman
2019-06-03 03:53:49

Somprasong Sripanya
2019-06-03 04:55:16

Greg Kourakos
2019-06-03 04:58:37

Luke Mason
2019-06-03 07:15:31

Todd Jones
2019-06-03 10:13:48

Joe Iovino
2019-06-03 10:35:37

Mariano Loisi
2019-06-03 13:16:08

Joel Reid
2019-06-03 18:59:02

André Nettermann
2019-06-03 20:14:02

Sjef Blaster
2019-06-03 20:19:20

Gary Houser
2019-06-03 22:24:18

Kevin Boogaard
2019-06-04 12:35:39

Gary Houser
2019-06-05 02:08:45

原文網址 Stephan Hillman
2019-06-01 10:39:29

The proofing bucket is complete!

翻譯年糕

原文網址 Stephan Hillman
2019-05-21 01:56:11

Any advice before I try to print this thing?

翻譯年糕

Toby Kirkby
2019-05-21 01:57:59

Toby Kirkby
2019-05-21 01:58:15

Cody Cockayne
2019-05-21 01:59:17

Keith Holmes
2019-05-21 02:59:53

Bobby Bonner
2019-05-21 03:59:07

Michael Van Kesteren
2019-05-21 05:54:39

Justin Parker
2019-05-21 15:24:52

Stephan Hillman
2019-05-22 02:19:21

原文網址 Stephan Hillman
2019-05-11 10:52:51

My first successful print!

翻譯年糕

Jose Elizondo
2019-05-11 10:53:11

Stephan Hillman
2019-05-11 10:57:38

原文網址 Stephan Hillman
2019-05-07 11:28:39

Well, first test print was a bust. I followed the instructions, leveled the plate, etc and then told it to print the standard cubic test pattern. I gave it a few hours to let the plate rise above the level of the resin and when I checked there was nothing attached to the plate. Suggestions?

翻譯年糕

Marc Fischer
2019-05-07 11:30:22

Danny Broekhuis
2019-05-07 11:31:27

Adam Horton
2019-05-07 11:34:36

Stephan Hillman
2019-05-07 11:47:39

Marc Fischer
2019-05-07 11:59:27

Stefan Giudici
2019-05-07 12:20:38

Danny Broekhuis
2019-05-07 13:00:35

Mikko Asikainen
2019-05-07 13:05:02

原文網址 Stephan Hillman
2019-05-07 00:16:24

My printer was delivered yesterday. This week I plan to open it up, look through the manual, get it set up, and do a test print. Any recommendations for a NOOB?

翻譯年糕

Spike Walker
2019-05-07 00:18:56