Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Aaron Morgan
2019-12-10 07:31:46

Chitubox light off delay and bottom light off delay both are set by default to 0...I checked the google doc but it's showing very different numbers, is there something I'm missing?

翻譯年糕

Chris Sawtelle
2019-12-10 07:54:37

Tiernan Messmer
2019-12-10 07:55:41

Scott Pavlich
2019-12-10 08:08:28

Aaron Morgan
2019-12-10 08:29:11

Scott Pavlich
2019-12-10 09:34:05

Aaron Morgan
2019-12-10 09:51:31

原文網址 Aaron Morgan
2019-12-10 00:42:21

anyone ever print a thin base layer on their build plate for better adhesion like people using casting resin do? anyone ever print a thin base layer on their build plate for better adhesion like people using casting resin do? 翻譯年糕

Mark Wells
2019-12-10 00:44:27

Aaron Morgan
2019-12-10 00:46:44

Mark Wells
2019-12-10 00:54:31

Aaron Morgan
2019-12-10 01:00:40

Andrew Sternglass
2019-12-10 01:12:51

Mark Wardle
2019-12-10 01:13:15

Aaron Morgan
2019-12-10 01:13:52

Ryan Neal
2019-12-10 01:14:26

Aaron Morgan
2019-12-10 01:16:03

Aaron Morgan
2019-12-10 01:17:40

Paul West
2019-12-10 01:18:39

Sen Kun
2019-12-10 01:19:24

Mark Wardle
2019-12-10 01:19:47

Scott Pavlich
2019-12-10 01:20:04

Sen Kun
2019-12-10 01:21:51

Aaron Morgan
2019-12-10 01:22:15

Aaron Morgan
2019-12-10 01:23:17

Sen Kun
2019-12-10 01:24:25

Gary Houser
2019-12-10 01:28:02

Sen Kun
2019-12-10 01:29:34

Scott Pavlich
2019-12-10 01:31:17

Will Koehler
2019-12-10 01:34:27

Aaron Morgan
2019-12-10 01:36:24

Scott Pavlich
2019-12-10 02:04:12

Richard Humble
2019-12-10 02:04:33

Smith Hayward
2019-12-10 02:25:47

Richard Humble
2019-12-10 02:39:07

Aaron Morgan
2019-12-10 03:03:43

Mike Michaels
2019-12-10 03:47:54

Ryan Vogt
2019-12-10 04:07:50

Smith Hayward
2019-12-10 04:30:23

Mike Fatchett
2019-12-11 07:18:27

原文網址 Aaron Morgan
2019-12-09 07:20:30

There are a few resin ring casting videos on YouTube but I was curious if anyone here found any of them particularly helpful in making a ring from start to finish?

翻譯年糕

原文網址 Aaron Morgan
2019-12-05 04:09:19

will a 4hr44 min print using 39ml of resin need to be topped off before it finishes?

翻譯年糕

Mark Wells
2019-12-05 04:10:41

Nick Graydon
2019-12-05 04:10:55

Mark Wells
2019-12-05 04:11:14

Jeremy Babcock
2019-12-05 04:11:29

Michael Martin
2019-12-05 04:12:17

Aaron Morgan
2019-12-05 04:12:18

Aaron Morgan
2019-12-05 04:12:28

Aaron Morgan
2019-12-05 04:12:46

Aaron Morgan
2019-12-05 04:13:26

Darren Juniper
2019-12-05 04:14:15

Aaron Morgan
2019-12-05 04:14:53

Paul West
2019-12-05 04:15:05

Kenneth Boshell
2019-12-05 04:15:13

Michael Martin
2019-12-05 04:15:15

Paul West
2019-12-05 04:16:18

Paul West
2019-12-05 04:16:55

Darren Juniper
2019-12-05 04:18:13

Kenneth Boshell
2019-12-05 04:19:15

Michael Martin
2019-12-05 04:22:43

Dustin Oliverius
2019-12-05 05:08:06

Paul West
2019-12-05 05:19:41

Michael Martin
2019-12-05 05:23:10

Richard Webb
2019-12-05 05:42:46

Seth Seth Dyte Dyte
2019-12-05 07:02:28

Seth Seth Dyte Dyte
2019-12-05 07:03:04

Robin Dovber Tunkel
2019-12-05 07:05:19

Jeremy Babcock
2019-12-05 08:05:35

Nipuna Gunarathne
2019-12-05 21:01:59

原文網址 Aaron Morgan
2019-12-05 02:20:45

Tried printing this pickleball paddle flat on the platform but it’s curling up a bit, should I print on an edge with supports instead?

翻譯年糕

Peter Teal
2019-12-05 02:41:21

Mark Wardle
2019-12-05 02:46:32

Aaron Morgan
2019-12-05 02:52:50

原文網址 Aaron Morgan
2019-12-04 06:15:50

Hey gang, I’m having trouble with adhesion after not printing for a few months. I see a slight outline of whatever design I’m trying to print on the feb but nothing on the build plate.
Resin doesn’t expire till March but it did sit in the vat a few days. Could that be my problem?
Tried printing stuff sliced in Chitubox as well as photon cube design on the included usb drive. Zero adhesion for either

翻譯年糕

Antonis Karydis
2019-12-04 06:19:10

Aaron Morgan
2019-12-04 07:04:14

Aaron Morgan
2019-12-06 00:57:07

原文網址 Aaron Morgan
2019-12-03 11:55:03

I'm getting zero adhesion for this model. I see an ever so slight outline of the model on the FEP. I ran the UV test, releveled but still am having no luck. I DO have my window open to vent the fumes and it's 35F outside...could that be the issue?

翻譯年糕