Anycubic Photon Printer Owners 造訪社團

原文網址 Casper Kirketerp-Helenius
2019-08-04 06:37:37

So. Bottom edge was supposed to be flat and parallel to the print plate. Obviously, it’s not.
I changed the FEP today, and adjusted it so it hit the same frequency (243hz) as the one that came factory mounted. Coincidense or related? Tough luck? First misprint in ages.

翻譯年糕

Casper Kirketerp-Helenius
2019-08-04 06:41:07

Jared Zadorozny
2019-08-04 06:57:19

Jared Zadorozny
2019-08-04 06:58:32

Casper Kirketerp-Helenius
2019-08-04 06:59:59

Kyle A. Wolfe
2019-08-04 07:18:11

Casper Kirketerp-Helenius
2019-08-04 07:19:30

Kyle A. Wolfe
2019-08-04 07:28:25

Casper Kirketerp-Helenius
2019-08-04 07:30:39

Kyle A. Wolfe
2019-08-04 07:31:19

Nicolas Tsagarides
2019-08-04 07:47:31

Casper Kirketerp-Helenius
2019-08-05 02:36:34

Jeremy Paakanen
2019-10-04 00:58:52

Casper Kirketerp-Helenius
2019-10-04 05:01:53

Jeremy Paakanen
2019-10-06 06:14:46

原文網址 Kyle Standring
2019-08-04 06:36:36

Do you guys use a glue or resin to join multi part models and models to their bases?

翻譯年糕

Yasu Tano
2019-08-04 06:45:25

Matt Hockenheimer
2019-08-04 06:47:45

James Cachia-Garrett
2019-08-04 06:47:53

Thomas Wright
2019-08-04 06:47:53

Yasu Tano
2019-08-04 06:48:48

Benjamin Oppenheimer
2019-08-04 06:50:55

James O'Keane
2019-08-04 06:53:04

Steve Nottingham
2019-08-04 06:55:16

Deane Salzwedel
2019-08-04 06:57:08

Fedor Pikus
2019-08-04 06:59:28

Mike Mullen
2019-08-04 07:49:55

Damien Greysis
2019-08-04 09:02:45

Stefan Ritchie
2019-08-04 09:10:42

Alexandria Wagner
2019-08-04 09:18:27

Rhiannon Beorn Van D
2019-08-04 09:30:17

Richard Russell
2019-08-04 10:11:56

Damien Greysis
2019-08-04 10:41:45

Randy Schaar
2019-08-04 11:30:26

Peter Ede
2019-08-04 13:31:06

Stefan Ritchie
2019-08-04 18:04:20

Arthur Withier
2019-08-04 19:42:23

Markus Müller
2019-08-04 20:10:39

原文網址 Nickolus Rodriguez
2019-08-04 06:34:37

Hello everyone, does anyone know of a program that will let me measure and scale STL and OBJ files by volume rather than size or percent??

翻譯年糕

原文網址 Terry Andrews Jr.
2019-08-04 05:55:31

Further steps taken as recommended by members of this group in an attempt to determine if my machine will in fact produce good prints.

翻譯年糕

Vinicius Silva
2019-08-04 08:27:13

Terry Andrews Jr.
2019-08-04 08:30:25

Vinicius Silva
2019-08-04 08:31:21

Terry Andrews Jr.
2019-08-04 08:31:52

Michael Pollard
2019-08-04 08:34:19

Vinicius Silva
2019-08-04 08:37:55

Michael Pollard
2019-08-04 08:39:15

Vinicius Silva
2019-08-04 08:41:15

Michael Pollard
2019-08-04 08:51:27

Vinicius Silva
2019-08-04 08:52:59

Michael Pollard
2019-08-04 08:55:46

Chris Graf
2019-08-04 09:31:29

原文網址 Peter Lynn
2019-08-04 05:54:54

Needs a clean up with the dremel. Like the results

翻譯年糕

Jason Howe
2019-08-04 07:06:05

Michael Zinski
2019-08-04 07:23:51

Peter Lynn
2019-08-04 07:57:16

Peter Lynn
2019-08-04 07:58:05

Michael Zinski
2019-08-04 07:59:56

Peter Lynn
2019-08-04 08:01:42

Jason Howe
2019-08-04 08:02:02

Peter Lynn
2019-08-04 08:03:53

Michael Zinski
2019-08-04 08:04:06

Peter Lynn
2019-08-04 08:04:17

Peter Lynn
2019-08-04 08:07:01

Jason Howe
2019-08-04 08:11:56

Peter Lynn
2019-08-04 08:29:50

Peter Lynn
2019-08-04 08:29:51

Peter Lynn
2019-08-04 08:32:22

Michael Zinski
2019-08-04 08:32:42

Peter Lynn
2019-08-04 08:32:52

Peter Lynn
2019-08-04 08:35:50

Michael Zinski
2019-08-04 08:42:20

Peter Lynn
2019-08-04 09:06:33

Kyle Calderwood
2019-08-04 10:47:12

Peter Lynn
2019-08-04 12:10:06

Kyle Calderwood
2019-08-04 13:30:38

原文網址 Andries Verhoef
2019-08-04 05:43:11

Hi guys need some help! Test cube printed ok at 60% size! After that i installed the latest firmware and recalibrated. After that the next 2 prints keep sticking to the fep. Any ideas on how to solve this or what could cause it?

翻譯年糕

Mike Tree
2019-08-04 05:53:17

Thomas Wright
2019-08-04 06:25:27

Stefan Giudici
2019-08-04 06:32:51

Andries Verhoef
2019-08-04 15:21:57

原文網址 Hugh Jeriolas
2019-08-04 05:15:12

Alright mates. I’ve had my printer for a week and printed nonstop flawlessly. Now my prints fall off the build plate between 25/50% complete. Leveled the bed many times, cleaned the bed spotless many time, and run 50 exposure time on bottom layer with 10 on all others. Any other suggestions? I’m using medium supports. Anycubic green resin.

翻譯年糕