Anycubic Photon Printer Owners 造訪社團

原文網址 Jon Roche
2019-07-14 19:08:14

After an eventual successful test print (5 attempts) and the obligatory Yoda print (2 attempts) I think I’m ready to jump in and play about designs. What software do you think is best for a newbie like me that takes it to the next level i.e. adding supports?

翻譯年糕

Kevin Lems
2019-07-14 19:10:11

Chasen Harris
2019-07-15 03:22:21

原文網址 Mickaël Le Mouël
2019-07-14 18:50:43

原文網址 Hattha Souvenir
2019-07-14 18:21:36

disturb the members. Please help me. This is the test result. "resin-test-50u.B100.2-20.photon" and how much should I choose exposure time so it's good. I notice the center has holes Caused by my files or my photon Lcd. ( grey rasin)

翻譯年糕

Richard Shapiro
2019-07-14 18:26:12

Kevin Lems
2019-07-14 18:27:49

Richard Humble
2019-07-14 18:27:52

Hattha Souvenir
2019-07-14 18:34:24

Hattha Souvenir
2019-07-14 18:36:42

Zena Andreou
2019-07-14 18:37:26

Hattha Souvenir
2019-07-14 18:41:52

Hattha Souvenir
2019-07-14 18:42:58

Mike Tree
2019-07-14 18:57:47

Robert James
2019-07-14 19:28:15

Richard Shapiro
2019-07-14 22:14:01

Hattha Souvenir
2019-07-14 22:42:04

Robert Maefs
2019-07-14 23:38:45

Bob Deblier
2019-07-15 19:23:37

Diego Tomas
2019-07-16 15:15:53

原文網址 Jeff Slaughter
2019-07-14 18:18:38

After the failure of a test print, I relevelled the platform and it's printed perfectly :)

翻譯年糕

Kevin Lems
2019-07-14 19:07:28

Jeff Slaughter
2019-07-14 19:08:36

Kevin Lems
2019-07-14 19:37:05

原文網址 Alison Wartenberg
2019-07-14 17:56:01

The moment I go in to support-settings, the model isn't on the platform anymore :/

翻譯年糕

Zena Andreou
2019-07-14 18:04:13

Alison Wartenberg
2019-07-14 18:05:17

原文網址 Tom Inglis
2019-07-14 17:07:03

Phew! That's about as close as it gets!

翻譯年糕

Richard Humble
2019-07-14 17:17:35

James Cachia-Garrett
2019-07-14 17:27:07

Levente Nagy
2019-07-14 17:28:23

Ionut Filea
2019-07-14 17:45:02

Timothy White
2019-07-14 17:47:58

Seth Seth Dyte Dyte
2019-07-14 17:54:58

John Smith
2019-07-14 17:56:11

Ines Silva
2019-07-14 19:03:29

Juan Pablo Bagnon
2019-07-14 20:43:09

Darren Donovan
2019-07-14 22:19:36

Richard Zeinner
2019-07-14 22:30:26

James Robinson
2019-07-14 23:30:34

Gustaf Sjögren
2019-07-15 00:49:13

Tom Inglis
2019-07-15 01:13:57

Ben Rawalt
2019-07-15 01:30:23

Ocie Ward
2019-07-15 02:45:09

Jawad Abuasabeh
2019-07-15 03:05:43

David Hargrove
2019-07-15 03:44:07

Scott Pavlich
2019-07-15 04:56:54

Per Bekker-Madsen
2019-07-15 05:36:17

Eros Benjamin
2019-07-15 06:17:18

Keif Davies
2019-07-15 06:32:54

Joel Reid
2019-07-15 12:11:22

原文網址 Richard Humble
2019-07-14 16:44:45

Bit of help please chaps.
I'm getting pretty poor surface finish. Anycubic black resin. 0.05 at 10 secs/layer based on the exposure test.

I've not had this problem before. Only changes are new batch of resin, AA firmware and z wobble upgrade. Z wobble has gone (no 2mm striping I had before) printed at 45 degrees.

Could this be over exposure?

翻譯年糕

Jose Sicairos
2019-07-14 17:42:44

Richard Humble
2019-07-14 17:51:59

Richard Humble
2019-07-14 18:54:54

Hakan Sckyz
2019-07-14 19:52:03

Richard Humble
2019-07-15 02:56:42

Scott Pavlich
2019-07-16 07:55:22

原文網址 Drew Cski
2019-07-14 16:02:04

Resin exposure test 50um and doesn’t seem right. Is this from bed being to low or too high?

Siraya Tech Blue

翻譯年糕

Susan Sioux Mercer
2019-07-14 16:15:09

Drew Cski
2019-07-14 17:41:06

Susan Sioux Mercer
2019-07-14 18:25:48

原文網址 Leevi Jordan
2019-07-14 15:22:20

So I have seen suggestions to use microfiber cloths instead of paper towels when cleaning to protect the FEP. Seems reasonable, but how do you guys clean the microfiber cloths? It doesnt seem like you would want to put liquid resin in your washing machine and even cured it seems like it would present problems

翻譯年糕

Nick Williams
2019-07-14 15:26:38