Anycubic Photon Printer Owners 造訪社團

原文網址 Mark Wardle
2019-05-16 03:17:35

ahhh crap forgot i set up a new computer and installed the software again. i forgot to add the settings for the resin. hmmm.. crap. oops. rookie mistake.

翻譯年糕

Eddie Bianco
2019-05-16 05:27:55

原文網址 William Michael Smith
2019-05-16 03:09:59

Got a couple bottles of this in today, I hope it works as well as advertised. I’m planning to print some robotic parts from it for a costume, so hopefully this stuff will hold up.

翻譯年糕

Sen Kun
2019-05-16 03:25:28

Benjamin Davis
2019-05-16 03:28:10

Sen Kun
2019-05-16 04:32:39

Andy Chung
2019-05-16 04:43:39

William Michael Smith
2019-05-16 05:24:23

Wesley Boynton
2019-05-16 05:29:55

Wesley Boynton
2019-05-16 05:30:33

原文網址 Fred Williams
2019-05-16 03:05:25

Still need to cleannit up a little, but I love the light blue color.

翻譯年糕

Robert Silvers
2019-05-16 03:24:58

Fred Williams
2019-05-16 03:27:25

Thomassen Ølf
2019-05-16 03:44:25

Thomassen Ølf
2019-05-16 03:44:41

Chris Comeau
2019-05-16 03:48:59

Kacper Pawłowski
2019-05-16 04:29:24

Fred Williams
2019-05-16 04:44:50

Fred Breton
2019-05-16 07:00:06

原文網址 David Nicholls
2019-05-16 03:01:28

Licensing question?

I've been asked to print some items off of Thingiverse. Can I charge for printing them or does this breach the creative commons license?

翻譯年糕

Derek Reihe
2019-05-16 03:02:43

David Nicholls
2019-05-16 03:04:40

Richard Humble
2019-05-16 03:04:53

Derek Reihe
2019-05-16 03:05:02

Derek Reihe
2019-05-16 03:05:17

Jeff Johnson
2019-05-16 03:11:41

Derek Reihe
2019-05-16 03:12:40

Mark Craggs
2019-05-16 03:13:11

Wesley Dowell
2019-05-16 03:15:16

Mark Craggs
2019-05-16 03:16:29

Mark Craggs
2019-05-16 03:19:34

Henry Adams
2019-05-16 03:54:46

Jeff Hicks
2019-05-16 03:58:09

Derek Reihe
2019-05-16 04:01:40

Alessandro Fonseca
2019-05-16 04:08:52

Stefan Giudici
2019-05-16 04:11:51

Gary Houser
2019-05-16 04:23:33

John Fulmer
2019-05-16 04:24:51

John Fulmer
2019-05-16 04:26:46

Matt Jourdain
2019-05-16 04:30:34

Ryan Turner
2019-05-16 04:41:25

Jeremy Indelicato
2019-05-16 04:55:33

Stefan Giudici
2019-05-16 04:57:30

Aaron Troxler
2019-05-16 05:01:07

David Nicholls
2019-05-16 05:02:16

Derek Reihe
2019-05-16 05:04:41

Ric Watts
2019-05-16 05:26:06

Trea Cotton
2019-05-16 05:26:51

Ric Watts
2019-05-16 05:26:59

Derek Reihe
2019-05-16 05:40:25

David Johnson
2019-05-16 06:06:10

Robert Silvers
2019-05-16 06:53:10

Robert Silvers
2019-05-16 06:55:00

Mark Craggs
2019-05-16 17:19:41

原文網址 Jose León
2019-05-16 02:14:49

Would this motor work as a replacement for my Photon's?

翻譯年糕

Toby Kirkby
2019-05-16 02:25:45

Jose León
2019-05-16 02:33:38

Jan Morávek
2019-05-16 03:15:35

Sen Kun
2019-05-16 03:31:51

Jose León
2019-05-16 03:41:01

Jose León
2019-05-16 15:55:48

原文網址 Josh Gerrietts
2019-05-16 02:10:06

What support settings do people use for miniatures?

翻譯年糕

Adam Widdowson
2019-05-16 02:13:36

Gary Houser
2019-05-16 04:11:50

Tim Moulton
2019-05-16 04:12:55

Gary Houser
2019-05-16 04:23:10

原文網址 Wojciech Majkut
2019-05-16 02:06:01

Gladiator sculpted in Blender. Printed at 0.02 with anycubic grey resin sliced in photon's (it's not hollowed). Had some lines, so a bit of fine sanding and army painter's grey primer were helpful.
Since CTB doesn't work for me I'll do some tests with Meshmixer on other models.

翻譯年糕

原文網址 Devin Wallace Simonsen
2019-05-16 02:01:58

so I got my 3 uv leds for my curing chamber and I've started to design one for printing (I may have gone a little overboard) so wanted to hear your thoughts before printing it.

it's printed in two parts that'll glue together using guide rods/holes and will have eight sections of mirror (one in each side/hole)... 2 of the uv leds will be placed under the top and angled down and one will be placed from near the bottom angled slightly up

翻譯年糕