Anycubic Photon Printer Owners 造訪社團

原文網址 Andres Vargas
2019-04-14 09:58:18

2 hours to go... Almost done the first part. ?

原文網址 Timmo Hellemann
2019-04-14 09:57:57

Anyone tried to print PCB solder stencils? Maybe the rough top surface might be some problem. But a stencil in 2 Minutes... think I have to try it

翻譯年糕

原文網址 Justin Miller
2019-04-14 09:52:33

Scaled down a life size model to a barbie size model. I'm always blown away by the level of detail on this printer.

翻譯年糕

Andres Vargas
2019-04-14 09:54:31

Andres Vargas
2019-04-14 09:54:36

Micheal Ashton
2019-04-14 10:08:41

Mathieu Tremblay
2019-04-14 10:23:07

Darren Donovan
2019-04-14 11:37:49

Leon Skopilianos
2019-04-14 12:28:09

Jananga Chandima
2019-04-14 13:46:38

Christian Sargent
2019-04-14 23:47:56

原文網址 Alexius Lim
2019-04-14 09:30:44

Arrived last friday but only had time to open it today! Excited

翻譯年糕

Eduardo Herrero Ayuso
2019-04-14 14:38:38

Alexius Lim
2019-04-14 14:42:44

Robert Thorhauer
2019-04-14 15:02:52

Eduardo Herrero Ayuso
2019-04-14 15:08:04

Eduardo Herrero Ayuso
2019-04-14 15:08:54

Alexius Lim
2019-04-14 15:37:28

Robert Thorhauer
2019-04-14 15:39:46

Kuba Kalinowski
2019-04-14 16:41:57

Alexius Lim
2019-04-14 16:49:32

原文網址 Ken Long
2019-04-14 09:07:39

another newbie question. How does one know whether the FEP on the vat on a brand new Photon has a protective film?

翻譯年糕

Richard Shapiro
2019-04-14 09:10:54

Sen Kun
2019-04-15 01:44:34

原文網址 Justin Ragsdale
2019-04-14 08:55:26

When you absolutely, positively HAVE to make sure the screw doesn’t fall off the driver and into the back of the case..... again... ?

翻譯年糕

Art Barrow
2019-04-14 09:00:45

Rick Gonzales
2019-04-14 09:02:21

Jake Larson
2019-04-14 09:12:36

Ed Wilson
2019-04-14 09:13:29

Ken Long
2019-04-14 09:20:17

Chad Elstad
2019-04-14 10:26:16

Jared Zadorozny
2019-04-14 12:42:00

David Nicholls
2019-04-14 15:49:37

Sam Smith
2019-04-14 16:09:09

Alwin Chan
2019-04-14 23:30:36

Derek Reihe
2019-04-15 09:05:46

Robert Silvers
2019-04-15 12:57:54

原文網址 Wade Wendorf
2019-04-14 08:06:19

Well, it looks like something is wrong with my Photon. It starts printing just fine, then the Z axis just, stops working. I had to cancel my print. I tried to raise Z with the screen controls, and it wouldn't do nothing, so I started spinning the screw by hand, and it kicked in and started moving.

Do I have a bad motor? This thing was new in the box. Not happy at the moment.

翻譯年糕

Ocie Ward
2019-04-14 08:22:48

Justin Ragsdale
2019-04-14 09:05:20

Wade Wendorf
2019-04-14 09:05:48

Wade Wendorf
2019-04-14 09:08:56

Wade Wendorf
2019-04-14 22:17:52

Wade Wendorf
2019-04-17 03:44:02

Wade Wendorf
2019-04-17 03:44:29

Jovan Du Toit
2019-05-03 05:53:35

Wade Wendorf
2019-05-03 05:54:55

Jovan Du Toit
2019-05-03 06:56:59

Wade Wendorf
2019-05-03 07:07:14

原文網址 Ken Long
2019-04-14 08:02:53

does anyone have a config (*.cfg) of the Photon for ChiTuBox v1.3.0 ? I dont see one in the files area.

翻譯年糕

Chris Wilander
2019-04-14 08:06:09

Ken Long
2019-04-14 08:46:49

Chris Wilander
2019-04-14 12:00:14

原文網址 Scott Quinn
2019-04-14 07:08:08

wow, pressing pause raised the print and shows you if it's adhered to the plate....

good guess Mr Quinn ? ? ? ?

翻譯年糕

Blake Moody
2019-04-14 07:13:12

Scott Quinn
2019-04-14 07:20:18

Blake Moody
2019-04-14 07:22:06

David McGyver
2019-04-14 07:24:35

Scott Quinn
2019-04-14 07:27:40

Scott Quinn
2019-04-14 07:50:03

Danny Lloyd
2019-04-14 07:57:11

David Nicholls
2019-04-14 16:48:20

Patrick Smith
2019-04-14 22:31:44

Connor Coultrup
2019-04-15 01:21:56

David McGyver
2019-04-15 06:02:46

Scott Quinn
2019-04-15 06:11:30

原文網址 Bob Smit
2019-04-14 06:39:47

Not perfect but alot better. I angeld the moddel at 45 degrees, used enhough supports and changed the light off delay to 6,5 seconds. Seems to work alot better.

翻譯年糕