Anycubic Photon Printer Owners 造訪社團

原文網址 Marco Wintermayr
2019-03-09 14:08:15

Hi. I got my photon yesterday and i was wondering how to change resin? Just pour it through the filter and wipe off the remaining resin with a tissue?

Thank you

翻譯年糕

Jure Slokar
2019-03-09 16:51:39

原文網址 Chris Wilander
2019-03-09 11:37:44

Any Far Cry 3 fans in here? Shark idol turned out pretty awesome, mix of AnyCubic grey and black. Not consistent patterns since I had to separately add a bit of each color in the middle of the night so wouldn't run out of resin but I really like it. Will do the other idols at some point as well.
https://www.myminifactory.com/…/3d-print-shark-relic-farcry…

翻譯年糕

原文網址 William David Cunningham
2019-03-09 11:37:01

原文網址 Jawad Abuasabeh
2019-03-09 10:28:43

What grease should I use for the screw?

翻譯年糕

Zalrohg Lekgolo
2019-03-09 10:33:15

James Bricknell
2019-03-09 10:35:40

Ed Tackett
2019-03-09 10:35:43

Ed Tackett
2019-03-09 10:36:22

Scott Avis
2019-03-09 10:40:06

Patrick Smith
2019-03-09 10:47:24

Puren Bulat
2019-03-09 10:57:28

Chad Elstad
2019-03-09 11:00:25

Ed Gaulton
2019-03-09 11:23:41

Todd Jones
2019-03-09 12:22:27

Jason Clements
2019-03-09 12:38:20

原文網址 Fred Breton
2019-03-09 10:12:29

Another batch of Duncan Louca 's Goblins for my Gobs army, came out great. Done with Monocure Rapid Clear.

翻譯年糕

Jake Morley
2019-03-11 04:35:35

Fred Breton
2019-03-11 04:54:30

Jake Morley
2019-03-11 12:55:55

Fred Breton
2019-03-11 12:56:33

Jake Morley
2019-03-11 12:57:11

原文網址 Nick Williams
2019-03-09 09:29:00

My only gripe about the validator. Anyone have a fix? (It’s mirrored. Easier to find islands if it was the same.)

翻譯年糕

Susan Sioux Mercer
2019-03-09 09:47:15

Paul Mendoza
2019-03-09 14:05:21

Zena Andreou
2019-03-09 14:48:25

Sen Kun
2019-03-09 16:00:27

Sen Kun
2019-03-09 16:01:10

Nick Williams
2019-03-09 16:24:51

Vinicius Silva
2019-03-09 20:49:52

Vinicius Silva
2019-03-09 20:51:10

Vinicius Silva
2019-03-09 20:52:00

Vinicius Silva
2019-03-09 20:54:39

Susan Sioux Mercer
2019-03-09 20:57:50

Vinicius Silva
2019-03-09 21:02:51

Vinicius Silva
2019-03-09 21:03:16

Susan Sioux Mercer
2019-03-09 21:40:27

Vinicius Silva
2019-03-09 22:36:33

Susan Sioux Mercer
2019-03-09 22:41:34

Vinicius Silva
2019-03-09 22:46:34

Nick Williams
2019-03-10 01:58:58

Paul Mendoza
2019-03-12 07:49:45

原文網址 David Howlett
2019-03-09 08:19:29

Frenchy :)

翻譯年糕

David Howlett
2019-03-09 08:19:52

Fred Breton
2019-03-09 08:22:23

Guajolote Messias
2019-03-09 08:26:08

Ryan Turner
2019-03-09 09:29:09

Dexter WG
2019-03-09 12:56:27

Francis Hui
2019-03-09 13:43:37

Léo Protopappas
2019-03-09 18:42:28

Adam Foster
2019-03-09 18:44:24

Guajolote Messias
2019-03-09 18:46:52

David Howlett
2019-03-09 23:06:42

David Howlett
2019-03-10 03:36:39

Susan Sioux Mercer
2019-03-10 11:35:00

David Howlett
2019-03-10 14:09:40

原文網址 Mark W
2019-03-09 07:07:52

YEEEHAWWWW!!!

Brett Isaacs
2019-03-09 11:55:19

原文網址 Alex Hung
2019-03-09 06:50:50

How hot is too hot? I took a temp gun to the Photon and got a reading of 46°C. I'm printing on my balcony and it gets to 6°C here so I bought an IKEA Lixhult and lined it with styrofoam insulation and threw in a 14W retile heating pad. I've had zero failed prints using this setup with Elegoo Blue and Anycubic Green but how hot is too hot for the LCD/electronics in the Photon?

翻譯年糕