Anycubic Photon Printer Owners 造訪社團

原文網址 Jay Thomas
2019-03-04 10:33:52

Chitubox newb here.. I have the values set for the build plate. And half of the values for printing. Can anyone point me in the right direction for the rest of the values after "light off delay"..

翻譯年糕

Benjamin Oppenheimer
2019-03-04 10:36:43

Benjamin Oppenheimer
2019-03-04 10:37:55

Jay Thomas
2019-03-04 10:38:22

Milton Maxson
2019-03-04 10:39:39

Jay Thomas
2019-03-04 10:40:38

Milton Maxson
2019-03-04 10:41:22

Jay Thomas
2019-03-04 10:42:28

Milton Maxson
2019-03-04 10:44:56

Jay Thomas
2019-03-04 10:45:21

Milton Maxson
2019-03-04 10:47:34

Jay Thomas
2019-03-04 10:47:40

Jay Thomas
2019-03-04 10:48:01

Milton Maxson
2019-03-04 10:49:40

Jay Thomas
2019-03-04 10:52:24

Benjamin Oppenheimer
2019-03-04 10:53:03

Jay Thomas
2019-03-04 10:53:56

Benjamin Oppenheimer
2019-03-04 10:54:21

Milton Maxson
2019-03-04 10:55:10

Jay Thomas
2019-03-04 10:56:52

Milton Maxson
2019-03-04 10:57:21

Jay Thomas
2019-03-04 10:58:34

Milton Maxson
2019-03-04 10:59:37

Jay Thomas
2019-03-04 11:00:04

Benjamin Oppenheimer
2019-03-04 11:10:34

Jay Thomas
2019-03-04 11:14:23

Daniel Yuen Ato
2019-03-04 13:02:44

Mario Reinh
2019-03-04 14:55:11

Benjamin Oppenheimer
2019-03-04 15:47:47

谢信福
2019-03-04 21:57:16

Milton Maxson
2019-03-04 22:12:27

原文網址 Alan Lautenslager
2019-03-04 09:59:20

Question: Are the vapors emitted off of the resin flammable? I ask this as the only space I have to set up my Photon is in our mechanical room. The room is 12 foot square and up against one of the concrete walls is the hot water heater, furnace and the water conditioner. The water heater and furnace are GAS fired. I do plan to connect the Photon to a fan feeding into a charcoal filter canister. I DO NOT have the ability to vent it out side.
Thank you

翻譯年糕

Mat Greeley
2019-03-04 11:20:14

Chad Elstad
2019-03-04 13:48:45

Tom Smith
2019-03-04 20:19:15

Chris Diaz
2019-03-04 22:20:58

原文網址 William David Cunningham
2019-03-04 09:03:44

What settings are required to print directly on the build plate? What settings are required to print directly on the build plate? 翻譯年糕

Nick Sugg
2019-03-04 09:04:52

Hector Felix
2019-03-04 09:04:54

Jean-François Meloche
2019-03-04 09:05:38

Reb O'Rourke
2019-03-04 09:06:27

David McGyver
2019-03-04 09:12:10

Stefan Giudici
2019-03-04 09:49:36

Jeffrey Seymore
2019-03-04 10:16:54

William David Cunningham
2019-03-04 11:23:09

William David Cunningham
2019-03-04 12:09:09

David McGyver
2019-03-04 12:19:34

Daniel Yuen Ato
2019-03-04 12:47:31

David McGyver
2019-03-04 12:50:51

Daniel Yuen Ato
2019-03-04 12:54:27

Gary Dodds
2019-03-04 16:48:38

Jean-François Meloche
2019-03-04 20:04:39

Gary Dodds
2019-03-04 20:48:16

原文網址 Ty Mansfield
2019-03-04 09:03:35

Can I buy Anycubic clear resin and add pigment to it?

翻譯年糕

Ben Trigg
2019-03-04 09:22:34

Mark Wardle
2019-03-04 09:42:05

Sen Kun
2019-03-04 16:43:39

Ben Trigg
2019-03-04 20:41:54

Vinicius Silva
2019-03-04 21:18:56

Vinicius Silva
2019-03-04 21:19:34

Garret Bertrand
2019-03-04 22:21:02

Ty Mansfield
2019-03-04 23:38:18

Garret Bertrand
2019-03-04 23:44:19

Scott Miller
2019-03-05 05:44:53

Peter Ede
2019-03-05 20:28:32

Richard Thomas
2019-03-07 00:52:49

原文網址 Casey Shiray
2019-03-04 08:18:35

Can anyone tell me why the base layer printed this way? Everything seems to have turned out fine.

翻譯年糕

Odie Fox
2019-03-04 08:26:08

Milton Maxson
2019-03-04 08:30:38

Mark Wardle
2019-03-04 08:36:58

Tim Vince
2019-03-04 18:37:31

Ed Del Rey
2019-03-05 11:00:48

Dustin Skye
2019-03-06 07:25:16

原文網址 Edoardo Belli
2019-03-04 07:21:17

Hi everyone. I have some problems with the Photon. I put to print a model but the printer after a short time gave the error you see in the picture. I tried to reboot, replace the usb drive and the file to print but I had the same problem. can you tell me what it is?

翻譯年糕