Anycubic Photon Printer Owners 造訪社團

原文網址 Mario Reinh
2019-02-28 07:38:24

today a model of Overwatch

翻譯年糕

Ricardo Frederiks
2019-02-28 16:00:26

原文網址 Daniel Kollar
2019-02-28 07:37:30

Do you wash all of your prints with water after IPA? I've noticed that print gets blurry (or it has to be like that) when I wash it with water (cold water)...In this case i'm talking about Anycubic green and yellow resins. I'm asking this because I can see that most of prints of other people is more clear than blurry or dark green. What is your experience?

翻譯年糕

Garret Bertrand
2019-02-28 07:57:07

Jarrod Smith
2019-02-28 08:05:11

Guti Gutmann
2019-02-28 14:45:09

Darren Tarbard
2019-02-28 14:55:14

Enbos Enkhbayar
2019-02-28 17:40:25

原文網址 Monica Ann Pedone
2019-02-28 07:16:05

Uggh. Switched over to the grey Anycubic from the Green Translucent. Reset the Setting on the Anycubic Photon Slicer. Things were great

Then I tried to make some prints using Chitubox. Nothing stuck (except to the FEP). Then I realized I have to reset the setting in Chitubox. All ready to go

Forgot to tighten the screws on the vat. At least it was sticking to the plate.
Hoping this try works!!!

翻譯年糕

Kelly Wilkins
2019-02-28 23:29:37

Monica Ann Pedone
2019-02-28 23:42:12

原文網址 Matheus Sirota
2019-02-28 06:27:49

Hey guys, are this parameters or z-axis issue? I’m using Anycubic green provided by the printer.

翻譯年糕

Théo Rehgab Rodier
2019-02-28 06:37:32

Stevan Meisoll
2019-02-28 06:41:08

Sen Kun
2019-02-28 07:08:09

El Ner Endem
2019-02-28 08:52:25

Marco Toni
2019-02-28 09:16:06

Philippe Maegerman
2019-02-28 16:19:40

Dennis Tomson
2019-02-28 20:33:50

Dennis Tomson
2019-02-28 20:34:18

Sen Kun
2019-02-28 20:52:02

Philippe Maegerman
2019-02-28 20:53:25

Sen Kun
2019-02-28 21:00:12

Philippe Maegerman
2019-02-28 21:19:02

Kelly Wilkins
2019-02-28 22:31:47

Kelly Wilkins
2019-02-28 22:32:14

El Ner Endem
2019-02-28 23:06:04

Kelly Wilkins
2019-02-28 23:06:46

Kelly Wilkins
2019-02-28 23:08:50

Kelly Wilkins
2019-02-28 23:08:52

Kelly Wilkins
2019-02-28 23:08:53

Kelly Wilkins
2019-02-28 23:09:24

Kelly Wilkins
2019-02-28 23:27:50

Dennis Tomson
2019-02-28 23:28:04

Kelly Wilkins
2019-02-28 23:28:28

Dennis Tomson
2019-02-28 23:29:04

Kelly Wilkins
2019-02-28 23:30:25

Dennis Tomson
2019-02-28 23:31:42

Dennis Tomson
2019-02-28 23:41:42

Andrew McKay
2019-03-01 09:55:32

Dustin Skye
2019-03-02 21:32:03

原文網址 Немања Видић
2019-02-28 06:02:46

Senertek castable resin. It is ok, but a little bit loose, I have to play around with settings.

翻譯年糕

El Ner Endem
2019-02-28 08:55:28

Немања Видић
2019-02-28 17:20:11

Iván Bronchales Garcia
2019-03-03 20:28:27

原文網址 Riley Esmond
2019-02-28 05:41:49

I’m looking for some tutorials on using casting/castable resin which ever it is that is used in the investment casting procedures. I am going to do my own research but figure some one here might have links to good info about the whole process from resin and printing through the whole casting process. Any help would be great! Thank you :)

翻譯年糕

Paul Tyer
2019-02-28 06:29:46

原文網址 Michael Muir
2019-02-28 05:34:57

Wanted to share my results from squaring the z rail to the screen, the offset/warping issue is much better so I can only assumed a tilted z rail had something to do with that!

翻譯年糕

原文網址 William David Cunningham
2019-02-28 05:29:27

Wheels for the car I'm building...

翻譯年糕

Nigel Ratcliffe
2019-02-28 05:41:17

Mortadella De Mortadellis
2019-02-28 05:52:18

Karl Stark
2019-02-28 06:12:19

William David Cunningham
2019-02-28 06:15:24

Jay Thomas
2019-02-28 10:03:20

Benjamin Oppenheimer
2019-02-28 11:21:19

Jay Thomas
2019-02-28 11:22:13

Benjamin Oppenheimer
2019-02-28 11:22:48

Jay Thomas
2019-02-28 11:23:47

William David Cunningham
2019-02-28 11:33:09

Benjamin Oppenheimer
2019-02-28 11:49:13

Benjamin Oppenheimer
2019-02-28 11:50:55

Jay Thomas
2019-02-28 11:52:53

William David Cunningham
2019-02-28 21:58:41

Kelly Wilkins
2019-03-01 00:05:26

Gary Hunt
2019-03-02 09:01:36

William David Cunningham
2019-03-02 10:47:06

Gary Hunt
2019-03-02 11:02:14

原文網址 Marc Pominville
2019-02-28 05:16:14

Hello all, Question, why in Chitu box sometime I want some support and it can't give me the support.... I saw some peoples make support in place much more complex place than me... is there setting to change somewhere to add support on head to be connected the shoulder

翻譯年糕

原文網址 Robert Silvers
2019-02-28 05:00:43