Anycubic Photon Printer Owners 造訪社團

原文網址 Chris Yarrow
2019-01-24 23:10:58

I’m giving some thought to an enclosure.

Would 2 PC cooling fans shift enough air?

I’m think one drawing clean filtered air in, and a second to extract it through another filter?

翻譯年糕

Rose Stumpwater
2019-01-24 23:12:58

原文網址 Chris Mitchell
2019-01-24 22:53:07

A friend of mine is doing test prints for a emperor titan model I am working on but is having issues with warping on some of the parts. I do believe that it may be done to a lack of supports. My question is what software are you all using to add custom supports?

翻譯年糕

Sean Poeschl
2019-01-24 22:53:48

Sean Poeschl
2019-01-24 22:55:41

Barry Masterson
2019-01-24 23:11:40

原文網址 Paul Harker
2019-01-24 22:48:53

My first reasonably decent print. Still lots to learn.

翻譯年糕

David Nicholls
2019-01-24 22:59:20

EJ Escanilla
2019-01-24 23:20:59

Paul Verkooijen
2019-01-25 00:43:03

David Nicholls
2019-01-25 00:44:12

Dave Landry
2019-01-25 01:27:40

Juan M. Puerta
2019-01-25 02:40:10

Paul Harker
2019-01-25 03:50:56

Mark Markleson
2019-01-25 11:02:24

EJ Escanilla
2019-01-25 11:20:43

Flint Read
2019-01-25 11:36:04

Juan M. Puerta
2019-01-25 19:25:43

原文網址 Ben Mitchell
2019-01-24 22:27:43

I tried googling this and I could not find answer.
If you have a long print and the Resin is running low.. can you safely add resin to the Job?

翻譯年糕

Derek Reihe
2019-01-24 22:29:18

David Nicholls
2019-01-24 22:31:44

Derek Reihe
2019-01-24 22:32:35

Matt Tilson
2019-01-24 22:39:27

Sen Kun
2019-01-24 23:08:01

原文網址 Greg Bauer
2019-01-24 22:15:27

While waiting for my printer I have downloaded the photon slicer and the chitubox slicer. My question on the chitubox slicer in the advance tab what should my settings be for bottom light pwm, light pwm, anti-aliasing on or off, and if on what level.

翻譯年糕

Jonas Lepsøy
2019-01-24 22:24:06

Greg Bauer
2019-01-24 22:44:43

Greg Bauer
2019-01-24 23:10:27

Mike Roof
2019-01-27 21:53:52

原文網址 David Ian Fisher
2019-01-24 20:56:16

Would really appreciate the wisdom of the group on this issue. First print using the included clear green resin and the test cube. Read the FAQ and all guidance before set up, so I paid extra attention to levelling etc. and all looked good... Until just over a third of the way through the print when I found it attached to the FEP. Clearly an adhesion/suction issue, but given it's the standard resin with the standard recommended settings I'm at a bit of a loss as to what went wrong and what to fix!

翻譯年糕

Sen Kun
2019-01-24 21:01:38

Christian Plösser
2019-01-24 21:01:48

Trea Cotton
2019-01-24 21:03:18

Christian Plösser
2019-01-24 21:03:30

Sen Kun
2019-01-24 21:04:39

Christian Plösser
2019-01-24 21:05:34

David Ian Fisher
2019-01-24 22:02:30

Sen Kun
2019-01-25 01:02:29

David Ian Fisher
2019-01-26 06:56:46

David Ian Fisher
2019-01-26 06:57:02

David Ian Fisher
2019-01-26 06:59:38

Sen Kun
2019-01-26 13:52:58

David Ian Fisher
2019-01-26 15:30:08

Bob Leschyna
2019-01-26 22:36:57

Sen Kun
2019-01-26 23:16:34

原文網址 Richard Riddell
2019-01-24 20:44:31

Loving this printer more and more.

翻譯年糕

原文網址 Bernie Horowitz
2019-01-24 20:44:20

Little pigs little pigs let me in

翻譯年糕

原文網址 Franir Hamdan
2019-01-24 20:41:21

Can you mix the anycubic resin with the monocure resin Rapid flex 100? If anyone has had any experience in this regard, are the details kept? Can you mix the anycubic resin with the monocure resin Rapid flex 100? If anyone has had any experience in this regard, are the details kept? 翻譯年糕

Kristian Domingo
2019-01-24 20:46:20