Anycubic Photon Printer Owners 造訪社團

原文網址 Lucas Milner
2018-11-17 09:50:33

How does the anycubic photon discern between 0.05 and 0.02 layering if all other settings are the same? It seems to me that it just 'sandwiches' the layers tighter. I'd expect some squashing in this case.

翻譯年糕

Chris Cardinal
2018-11-17 09:51:57

Lucas Milner
2018-11-17 09:55:39

Max Hancock
2018-11-17 10:19:32

Stefan Giudici
2018-11-17 10:40:41

Lucas Milner
2018-11-17 10:47:12

Lucas Milner
2018-11-17 10:49:21

Sen Kun
2018-11-17 14:14:13

Vinicius Silva
2018-11-17 18:00:04

Lucas Milner
2018-11-18 06:40:33

原文網址 Javier Barbero
2018-11-17 09:42:48

Tiny tiny Viking ship

翻譯年糕

Jason Kelly
2018-11-17 09:49:43

Mark A. Siefert
2018-11-17 10:05:50

原文網址 Dave Williams
2018-11-17 09:18:06

Thanks for the join, I ordered my photon this morning, my first resin printer, I used from but trying to get the print quality I wanted was a no go, so after reading through comments on here I hope I don't get as many problems with print adhesion as the FDM, my main hobby is designing dioramas, and building and painting figures

翻譯年糕

Lucas Azd
2018-11-17 09:30:41

Ekaterina Vitalyevna
2018-11-17 12:11:28

原文網址 Cristobal Rubilar Ayala
2018-11-17 08:39:57

原文網址 Lucas Azd
2018-11-17 08:27:15

Printing the spear now. Not sure if I like his skin colour but overall good for 1 night of painting.

翻譯年糕

Sterling Osment
2018-11-17 08:56:15

Lucas Azd
2018-11-17 08:57:19

Sterling Osment
2018-11-17 09:00:45

Chris Meijer
2018-11-17 16:27:56

Lucas Azd
2018-11-17 17:28:17

Vaughan Lundin
2018-11-17 17:52:51

Lucas Azd
2018-11-17 18:42:43

Vaughan Lundin
2018-11-17 20:00:30

Lucas Azd
2018-11-17 20:08:48

Nard Janssens
2018-11-18 01:50:24

Scott Young
2018-11-18 04:01:26

Lucas Azd
2018-11-18 08:29:43

Lucas Azd
2018-11-18 08:30:31

原文網址 Chris Welton
2018-11-17 07:16:28

Just started experimenting with nail polish on translucent prints. The beard guy is half unfinished half polished.
Others using nail polish. What do you buy and how do you apply it? I used the little brush and it left brush stroke on flat parts.

翻譯年糕

Mark Wardle
2018-11-17 07:30:05

Chris Welton
2018-11-17 07:30:51

Fred Breton
2018-11-17 07:31:06

Chris Welton
2018-11-17 07:31:35

Mark Wardle
2018-11-17 07:32:21

Mark Wardle
2018-11-17 07:33:04

Chris Welton
2018-11-17 07:33:06

Chris Welton
2018-11-17 07:34:02

Fred Breton
2018-11-17 07:34:49

Chris Welton
2018-11-17 07:37:02

Fred Breton
2018-11-17 07:37:29

Seona van der Pol
2018-11-17 08:17:13

Chris Welton
2018-11-17 10:37:18

Lou Steinritz
2018-11-17 11:14:22

Chris Welton
2018-11-17 11:15:02

原文網址 Chris Welton
2018-11-17 06:53:08

I've been looking getting this ResinAway of ultra clear prints, but It's out of stock EVERYWHERE. Is that normal?

翻譯年糕

Mark Wardle
2018-11-17 07:13:18

Chris Welton
2018-11-17 07:14:54

Mark Wardle
2018-11-17 07:16:32

原文網址 Simon Jackson
2018-11-17 06:13:41

So what causes the 'Thunk' noise (and sometimes a noticeable jerk) as the build plate travels? It seems inconsistent....sometimes it does it, sometimes not, sometimes at a point when you might think the model is peeling from the FEP. sometimes on the way back down. So...Screw backlash?, Motor bearing preload springs returning the whole rotor and shaft to it's proper position, firmly against the opposite bearing...what is your theory?

翻譯年糕

Derek Reihe
2018-11-17 06:23:53

Simon Jackson
2018-11-17 06:41:22

Mark Wardle
2018-11-17 06:48:59

Sen Kun
2018-11-17 14:23:59

原文網址 Lukáš Antes
2018-11-17 05:56:25

what should I use for painting models on gray from aycubic red resin? what should I use for painting models on gray from aycubic red resin? 翻譯年糕

Fahrid van Uitert
2018-11-17 06:06:47

Clint Primley
2018-11-17 08:56:16

Frank Brechmann
2018-11-17 15:04:49

原文網址 Darron Rodrigues
2018-11-17 05:05:17

What’s the right type of respirator we should be using during the cleanup? I’m more concerned with the toxicity of the IPA fumes than the resin. With winter coming it’s difficult to keep the workshop ventilated and warm.

翻譯年糕

Marat Bedoev
2018-11-17 05:09:56