Anycubic Photon Printer Owners 造訪社團

原文網址 Lucas Milner
2018-11-16 07:41:03

Day2b, hollowed to 2mm, added more supports (heavy mode) this time, went with a ~30 degree tilt.
One sword broke off when removing supports (I don't think I even needed supports in this area).
There is liquid trapped inside and dimples at the support points.
How should I deal with hollowed prints?
These are 80mm in height.

翻譯年糕

Richard Shapiro
2018-11-16 07:53:05

Richard Shapiro
2018-11-16 08:05:57

Lucas Milner
2018-11-16 08:06:37

Richard Shapiro
2018-11-16 08:08:53

Stefan Giudici
2018-11-16 11:37:38

Lucas Milner
2018-11-16 11:40:44

Richard Burrell
2018-11-16 16:06:56

原文網址 Lucas Milner
2018-11-16 07:35:33

Day 2a, learning a lot.
I think I needed more supports in this area, hollowed out to 1mm, I saw resin inside so I decided to pop the back of the shell at the failed area, surprisingly brittle, it shattered instead of punching the hole.
I think I will choose to hollow it at 2mm next time.

翻譯年糕

Nick Williams
2018-11-16 08:49:50

Mike Bauers
2018-11-16 08:56:24

Lucas Milner
2018-11-16 08:57:12

Lucas Milner
2018-11-16 08:58:49

Stefan Giudici
2018-11-16 11:06:04

Stuart Presley
2018-11-16 12:55:43

Zena Andreou
2018-11-16 14:25:34

原文網址 David J Hayes
2018-11-16 06:47:33

So is chitu box better than the B9 create for supports? Trying to decide if I should switch

翻譯年糕

Peter Ede
2018-11-16 07:03:04

Nick Williams
2018-11-16 07:21:14

Trea Cotton
2018-11-16 08:03:22

谢信福
2018-11-16 10:59:57

Richard Burrell
2018-11-16 16:11:39

Scott Young
2018-11-16 16:18:06

Nick Williams
2018-11-16 16:21:13

谢信福
2018-11-16 19:16:22

原文網址 Lucas Azd
2018-11-16 06:45:39

Another one for the diorama. It was quite easy the fastest I've painted so far, 3 hours and it was done.

翻譯年糕

Jeff Schaefer
2018-11-16 08:44:45

Sterling Osment
2018-11-16 08:52:55

Thomas Pascoe
2018-11-16 10:03:54

Lucas Azd
2018-11-16 10:05:24

Thomas Pascoe
2018-11-16 10:06:00

Lucas Azd
2018-11-16 10:07:40

Lucas Azd
2018-11-16 10:07:52

Loek Roovers
2018-11-16 15:08:08

Lucas Azd
2018-11-16 15:21:34

Adam Green
2018-11-16 18:35:09

Bob Heron
2018-11-16 22:08:12

Ekaterina Vitalyevna
2018-11-16 22:31:55

原文網址 Thomas Wright
2018-11-16 05:56:07

I got my printer today! It's all setup and printing the test cube right now. When I did the paper calibration, it really feels as though the build plate is not truly flat. The paper could be pulled easier on one side than another. Is that me not flattening it properly or can the plate actually be not real flat?

翻譯年糕

Stefan Giudici
2018-11-16 06:03:38

Derek Heath
2018-11-16 06:09:18

El Ner Endem
2018-11-16 06:17:46

Robert Mako Sharkey
2018-11-16 06:21:25

Thomas Wright
2018-11-17 00:54:12

原文網址 Coral Night
2018-11-16 05:32:51

Is there a better power cord for the printer ???

Mine isnt working after 1 week. Is there a better power cord for the printer ???

Mine isnt working after 1 week. 翻譯年糕

Coral Night
2018-11-16 05:33:39

Kevin Rank
2018-11-16 05:45:44

Amy Liao
2018-11-16 09:24:31

原文網址 Róbert Jurčo
2018-11-16 04:43:06

Mu first try with the photon. Really impressed, but I need to practice with supports to make it perfect. Sliced with Formware at 70microns

翻譯年糕

原文網址 Marcin Kaleta
2018-11-16 04:37:28

Any advice on red and orange Anycubic resin? I ordered orange before I knew it could be so problematic. Any advice on red and orange Anycubic resin? I ordered orange before I knew it could be so problematic. 翻譯年糕

Marcin Kaleta
2018-11-16 04:38:09

John Oomen
2018-11-16 04:41:30

Mickael Alaen
2018-11-16 16:40:04

Mickael Alaen
2018-11-16 16:41:03

Marcin Kaleta
2018-11-16 17:51:02

Mickael Alaen
2018-11-16 17:52:56

Mickael Alaen
2018-11-16 17:55:49

原文網址 Brayden Funk
2018-11-16 04:24:52

This is my first 3D printer, so I'm probably screwing up something obvious.

This is how the majority of my prints are coming out. I've gotten a few successful ones, but about 90% of them seem to be printing the supports okay and the coming out squished like this after that.

Thanks for any help you guys can provide.

翻譯年糕

Brayden Funk
2018-11-16 04:26:30

Brayden Funk
2018-11-16 04:27:12

Chris Gough
2018-11-16 06:30:28

原文網址 Giancarlo Arriola
2018-11-16 04:12:57

Although I don't own this printer, I am a huge fan of it from the results it can pump out. But I am still on the fence because of that small build volume.
I was wondering if anyone knows of some info that Anycubic might be in working on a larger build volume for this printer while keeping it affordable? That would be the selling point for me since they've already worked out most of the kinks on this one, they wouldn't have that many bugs to work out on a larger version.

翻譯年糕

Brandon Ray
2018-11-16 04:37:21

Stefan Giudici
2018-11-16 04:38:13

Sterling Osment
2018-11-16 10:14:59

討論主題

發文排行榜

回文排行榜

熱門關鍵字