Anycubic Photon Printer Owners 造訪社團

原文網址 Matthew Parker
2018-11-16 04:03:45

Hi all! Some time ago I moved my extruder motor from the factory position and replaced the metal assembly on top with 3D printed parts to fit the new configuration. These parts have degraded, and I can no longer keep my extruder pressure (against the filament) tight enough against the filament. As well, a one of the screw holes inside the motor has become stripped, so I only have three screws holding it together.

Where can I find a good replacement motor and metal assembly for it?

翻譯年糕

Jeremy Lauzon
2018-11-16 04:07:32

Matthew Parker
2018-11-16 07:34:12

原文網址 Simon Jackson
2018-11-16 03:56:58

Phumex!...this should reduce the stink! It fits in place of the rear grill and uses a 12V 90mm fan I happened to have and a standard 210mm active carbon cooker-hood filter. I suppose the design can be easily adjusted to fit other fans....I noticed that most fans near that size are 92mm for some odd reason.

翻譯年糕

Nick Santana
2018-11-16 04:03:09

Simon Jackson
2018-11-16 04:04:49

Marcin Kaleta
2018-11-16 04:45:13

Luca Pellegrino
2018-11-29 17:14:02

Simon Jackson
2018-11-29 17:49:53

Luca Pellegrino
2018-11-29 17:53:18

Simon Jackson
2018-11-29 17:54:50

Simon Jackson
2018-11-30 11:38:32

Adam Fitzgerald
2019-03-04 02:13:44

Simon Jackson
2019-03-04 04:12:26

Adam Fitzgerald
2019-03-04 04:14:27

Simon Jackson
2019-03-04 04:16:51

Adam Fitzgerald
2019-03-04 04:20:08

Simon Jackson
2019-03-04 04:21:39

Adam Fitzgerald
2019-03-04 05:26:23

Simon Jackson
2019-03-04 05:36:02

Adam Fitzgerald
2019-03-04 05:36:48

原文網址 Tom Satchwell
2018-11-16 03:27:06

First proper difficult print with the chitubox slicer. Excellent support system, made it very easy. Had to add about 10 extra small supports after auto support to clear islands.

翻譯年糕

Philippe Maegerman
2018-11-16 03:35:59

Adam Horton
2018-11-16 03:38:48

Kostas Filosofou
2018-11-16 04:07:41

Tom Satchwell
2018-11-16 04:32:06

Kostas Filosofou
2018-11-16 04:34:53

Tom Satchwell
2018-11-16 05:08:26

Angelus Nox
2018-11-16 16:10:23

Angel Antelo Martinez
2018-11-17 08:00:39

Angel Antelo Martinez
2018-11-17 08:01:21

Tom Satchwell
2018-11-17 09:55:48

原文網址 Ritmo Pat
2018-11-16 01:33:08

Had to make this one for the 1st prototype fit check

翻譯年糕

原文網址 Vinicius Silva
2018-11-16 01:17:21

Nick Williams
2018-11-16 01:19:10

Vinicius Silva
2018-11-16 01:36:42

Vinicius Silva
2018-11-16 01:37:12

Vinicius Silva
2018-11-16 01:39:26

Nick Williams
2018-11-16 01:39:26

Vinicius Silva
2018-11-16 01:39:58

Vinicius Silva
2018-11-16 01:42:11

Fernando Gómez Galloso
2018-11-16 01:51:04

Philippe Maegerman
2018-11-16 03:29:55

Vinicius Silva
2018-11-16 03:31:35

Lucas Azd
2018-11-16 07:07:06

Vinicius Silva
2018-11-16 08:37:52

Lucas Azd
2018-11-16 08:49:27

原文網址 James Paull
2018-11-16 01:06:42

So Resin Away melted my Ultrasonic cleaner lid to the machine and also turned it to mush. also not sure how to empty the vat since the edge of the vat is not sealed between the ABS casing of the machine and the fluid would leak into the working parts.

翻譯年糕

Frank Shelby
2018-11-16 01:13:51

James Paull
2018-11-16 01:15:59

Paul Tyer
2018-11-16 01:23:07

Richard Burrell
2018-11-16 01:24:02

James Paull
2018-11-16 01:24:19

Liz Matzelle
2018-11-16 01:26:02

James Paull
2018-11-16 01:29:41

Paul Tyer
2018-11-16 01:32:11

Richard Burrell
2018-11-16 01:38:02

James Paull
2018-11-16 02:04:45

Jack Sweek
2018-11-16 03:49:28

Stefan Giudici
2018-11-16 11:09:33

Paul Wills
2018-11-16 11:35:02

原文網址 James Mcloughlin
2018-11-16 00:56:07

Having a slight issue here, only the tops of my prints working.

翻譯年糕

Kevin Lems
2018-11-16 01:30:40

James Mcloughlin
2018-11-16 01:31:52

Kevin Lems
2018-11-16 01:35:26

Sen Kun
2018-11-16 02:31:03

James Mcloughlin
2018-11-16 02:32:20

Kevin Lems
2018-11-16 02:32:29

Sen Kun
2018-11-16 02:36:19

James Mcloughlin
2018-11-16 02:37:15

Sen Kun
2018-11-16 02:38:20

James Mcloughlin
2018-11-16 02:39:10

Sen Kun
2018-11-16 02:40:49

Dennis Tomson
2018-11-16 03:11:54

原文網址 Жека Запал
2018-11-16 00:24:26

Hello there,
I have my new Anycubic photon today.
I've had first print failed.
I thought it was maybe model error.
Than I searched for another, opened in slicer, added supports,sliced.
Tryied in photon, but still no use.
As I see on internet, the problem is that model dont stick to platform itt sticks to bottom vat or smt, if you can see on that pic.
Any solutions?

翻譯年糕