Anycubic Photon Printer Owners 造訪社團

原文網址 Fred Breton
2018-08-17 15:42:54

I like this one. Broke the a part of the bolter magazine on the left when i was removing the suports. Done with Monocure Rapid clear and pigments kit.
50um, 12sec, 1sec offtime,70sec bottom,6 layers.

翻譯年糕

原文網址 Paul Tyer
2018-08-17 14:44:39

Just playing around with the new NXT GEN snow white resin from FunToDo, excellent results as always.

翻譯年糕

原文網址 Stefan Giudici
2018-08-17 14:32:01

Ha, tried a clear resin litho

翻譯年糕

原文網址 Lennart Johansson
2018-08-17 11:34:39

As I was guessing earlier I seems like the photon prints a single full layer some time into the print... This time it stuck to the print so I could see it clearly.

First I thought it was me that forgot to run the print mode file after the exposure test. But I really did do that.

翻譯年糕

Lennart Johansson
2018-08-17 11:41:07

Stefan Giudici
2018-08-17 12:00:07

Lennart Johansson
2018-08-17 12:05:41

陳彦廷
2018-08-17 13:21:49

Amy Liao
2018-08-17 15:08:02

Lennart Johansson
2018-08-17 15:47:40

César Fernández
2018-08-17 16:19:15

Daniel Velarde Kübber
2019-05-01 04:22:18

César Fernández
2019-05-01 15:38:04

原文網址 Cameron Ramoly
2018-08-17 11:05:57

is this a common thing when applying auto-support? it doesn't seem..... effective

翻譯年糕

原文網址 Ronald Bondoc
2018-08-17 09:35:56

Print from over the weekend that I finally got to put a coat of primer on today.

翻譯年糕

原文網址 Dombi Szilárd
2018-08-17 07:29:57

FTD Snow White NXT GEN test print after 30min under UV light next to my white wall.
I shaked the bottle very hard for half a minute. Is that normal?
As the photos from the internet I expected a white color not yellow...

翻譯年糕

原文網址 Taeo Gerrits
2018-08-17 07:21:15

oh, one more question. I always end up throwing my build plate out of alignment when I'm popping off the prints, forcing me to re-level it for every print job. Is there a better way to hold it to keep that from happening, or do I just keep doing it this way?

翻譯年糕

原文網址 Taeo Gerrits
2018-08-17 07:04:22

You can only see it under the perfect lighting conditions, but my FEP film is starting to get little dimples from the printed supports. I've only been at this for a week, however. Am I doing something wrong? How long should the FEP film last? It seems to have a bit scratched by my paper towel too, which is a bit surprising

翻譯年糕

原文網址 Kristopher Groves
2018-08-17 06:26:58

Just waiting for my carbon filter material.

Fan adapter https://www.thingiverse.com/thing:3047938

Backplate https://www.thingiverse.com/thing:3053213

Fan/Filter housing (will need to edit this part to allow power wires for the fan, I just cut mine out after the fact) https://www.thingiverse.com/thing:2752346

Fan https://www.amazon.com/AC-Infinity-Cooling-Ve…/…/ref=sr_1_2…

Filter material https://www.amazon.com/…/B00…/ref=oh_aui_detailpage_o00_s00…

翻譯年糕