Anycubic Photon Printer Owners 造訪社團

原文網址 Rob van Doorn
2020-01-18 23:12:10

Okay, is there a shorter test print than the Photon Cube around?

翻譯年糕

Michael D Showalter
2020-01-18 23:14:44

Pierre Eichel
2020-01-18 23:23:06

Rob van Doorn
2020-01-18 23:58:40

Rob van Doorn
2020-01-19 05:29:37

Pierre Eichel
2020-01-19 07:03:47

Pierre Eichel
2020-01-19 07:03:57

Bob Deblier
2020-01-20 21:49:01

原文網址 Kel Gon
2020-01-18 23:11:38

I just change a new fep for the first time. My screwdriver accidentally made a dent on the fep. I read here somewhere the using a heat gun and and it actually works. Lol.

翻譯年糕

Thrall Hood
2020-01-18 23:14:15

Kel Gon
2020-01-18 23:15:47

Jim Nelson
2020-01-18 23:31:19

Evan Rosario
2020-01-19 02:05:43

David Collinson
2020-01-19 09:30:32

Kel Gon
2020-01-20 04:07:37

Evan Rosario
2020-01-20 04:08:36

Gary Houser
2020-01-22 04:13:30

原文網址 Rob van Doorn
2020-01-18 23:01:42

I'm going to flash the firmware on my Photon S from v3.something to v5.0.2. Do I need to relevel after flashing the firmware? I have my levels juuuuust right... ;-)

翻譯年糕

Brendan Wood
2020-01-18 23:09:33

Rob van Doorn
2020-01-18 23:10:05

Brendan Wood
2020-01-18 23:10:26

Rob van Doorn
2020-01-18 23:11:17

原文網址 Peter Ring
2020-01-18 22:57:49

Is this an error with chitubox? I have never seen these werid lines before... They appear on all layers except the very last one.

翻譯年糕

原文網址 Lestat De Lioncourt
2020-01-18 22:43:59

I'm not a 3d modelest but I need the blues circle gone but also to leave the cut out in the green.. How to I do this?

翻譯年糕

Lestat De Lioncourt
2020-01-18 22:44:23

Aaron McCommon
2020-01-18 22:45:55

Marko Sallinen
2020-01-18 22:46:53

Lestat De Lioncourt
2020-01-18 22:47:13

Lestat De Lioncourt
2020-01-18 22:47:40

原文網址 Podok T. Mad
2020-01-18 22:29:19

I'm at a loss, I've tried to print these two minis 4 times, small supports, medium supports, different angles, nothing is working. Using the anycubic photon S,. 02 layer at 4 second exposure, anycubic standard grey resin. It's like it just stopped for some reason. Bed is level, lcd is working, fep is good. Any ideas?

翻譯年糕

Luca Cavallari
2020-01-18 22:35:58

Haydn Nelms
2020-01-18 22:49:57

Spencer Griffin
2020-01-21 20:54:41

Joe Perfect
2020-01-21 22:09:54

Spencer Griffin
2020-01-22 04:27:35

原文網址 Mike Rea
2020-01-18 22:24:42

So Anycubic sent me a Photon with a stripped screw in the FEP plate. I've never touched the FEP plate before.

Managed to get it off by twisting the two plates with pressure, but I thought I'd share :)

翻譯年糕

Ben Johnston
2020-01-18 22:28:06

Mike Rea
2020-01-18 22:29:33

Ben Johnston
2020-01-18 22:31:07

原文網址 Simone Ornati
2020-01-18 22:11:15

Any ideas on what's causing those horizontal artifacts?

翻譯年糕

Mark Reynolds
2020-01-18 22:21:32

Kelvin Pang
2020-01-18 22:22:12

Stefan Giudici
2020-01-18 22:28:11

Simone Ornati
2020-01-18 23:08:42

Stefan Giudici
2020-01-18 23:23:43

Simone Ornati
2020-01-18 23:43:00

Simone Ornati
2020-01-19 03:50:08

Gamee Designee
2020-01-19 05:02:39

Troy Wood
2020-01-19 16:34:02

Luke Mason
2020-01-19 18:08:50

原文網址 Gavin Fennell
2020-01-18 21:38:45

Hi all. Just did my test print on my photon and it has failed on the wording that’s says photon. Any ideas on what could have caused it? Used eleggo grey and just what the settings were for the test print. Thanks ?

翻譯年糕