Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Luca Cavallari
2020-02-29 19:18:53

I keep not understanding how to read this... Is 6 the good one? Seems a lot to me for a 30 um layer height test ?

翻譯年糕

Ray Sears
2020-02-29 19:38:17

Luca Cavallari
2020-02-29 23:52:25

Niall Forrester
2020-03-01 01:53:54

Chris Robinson
2020-03-01 01:57:08

Nipuna Gunarathne
2020-03-01 02:00:53

Ray Sears
2020-03-01 04:17:10

Ray Sears
2020-03-01 04:49:20

Luca Cavallari
2020-03-01 05:01:10

Tom Sargison
2020-03-01 05:52:49

Chris Robinson
2020-03-01 08:38:33

Ray Sears
2020-03-01 08:40:09

原文網址 Luca Cavallari
2020-01-28 06:02:59

In the end I'm here to ask the fateful question too... ?
Which One? 7?? 8?? (Seems a lot of exposure ? )
P.S. this color it's really hard to see, I had to try a lot of light sources to make a decent picture

翻譯年糕

Mark Reynolds
2020-01-28 06:06:37

Luca Cavallari
2020-01-28 06:54:30

Niall Forrester
2020-01-28 12:59:36

Zena Andreou
2020-01-28 14:17:48

Christian Plösser
2020-01-28 18:52:17

Bob Snyder
2020-01-29 00:57:33

James Swan
2020-01-29 01:08:25

Luca Cavallari
2020-01-29 06:19:21

Sander van Deijl
2020-01-30 01:51:01

原文網址 Luca Cavallari
2020-01-06 22:18:17

Miniature, 28 mm scale, normal human figures: do you hollow them? and if yes, how thin you set the walls?

翻譯年糕

David N. Amis
2020-01-06 22:20:30

Geoffrey Ian Ward
2020-01-06 22:20:50

Jeremy Swigart
2020-01-06 22:23:34

Joel Reid
2020-01-07 01:02:48

Scott Pavlich
2020-01-07 01:15:33

James Hendrix
2020-01-07 01:55:39

Caio Donini
2020-01-07 03:47:39

Will Koehler
2020-01-07 10:12:43

Jlee Usn
2020-01-07 11:24:36

Nicholas Corea
2020-01-07 11:51:59

Vincent Balmont
2020-01-07 17:34:59

Marcin Jażdżewski
2020-01-07 18:17:56

Tyler Bunty
2020-01-07 18:24:42

Gary Noble
2020-01-07 19:10:50

Patrick Morgan
2020-01-07 21:03:07

Tyler Bunty
2020-01-07 21:20:55

Patrick Morgan
2020-01-07 22:23:56

Adam Green
2020-01-08 00:01:25

Neil Joseph
2020-01-08 00:57:29

Neil Joseph
2020-01-08 00:58:16

Tyler Bunty
2020-01-08 04:12:22

Bob Deblier
2020-01-10 22:12:48

Joel Reid
2020-01-11 13:54:20

Joel Reid
2020-01-11 13:57:57

原文網址 Luca Cavallari
2019-12-24 15:12:53

I searched among the posts but I think is a new (and maybe stupid) question:
If I'm going to make 2 prints consecutively, it's enough to remove the first object and start to print again or should I clean the plate with ipa before the second round?

翻譯年糕

Sydnee Davidson
2019-12-24 15:14:38

Rhiannon Beorn Van D
2019-12-24 15:18:47

Luca Cavallari
2019-12-24 15:20:02

Stefan Giudici
2019-12-24 15:24:26

Sydnee Davidson
2019-12-24 15:25:46

Sydnee Davidson
2019-12-24 15:27:46

Luca Cavallari
2019-12-24 15:29:47

Jim Nelson
2019-12-24 16:33:24

Spencer Griffin
2019-12-24 17:46:08

Luca Cavallari
2019-12-24 18:07:23

Chris Bondy
2019-12-24 18:18:04

原文網址 Luca Cavallari
2019-12-18 18:18:12

It seems like all my printing problems were caused by the USB ?

Now just a question...I read that everyone here talks about the green resin that comes with the printer... Well, I bought the Photon on black Friday offer with an additional 500 ml grey resin. I received the grey resin and the printer with 2 distinct spedition (I received first the resin, so thanks for the heart attack), but in the printer package I found no resin. Is It correct or I should have received also the green one?

翻譯年糕

Davide Rizzo
2019-12-18 18:29:52

Jeppe Løvstrøm Frederiksen
2019-12-18 18:44:35

原文網址 Luca Cavallari
2019-12-15 22:01:47

Hello, I bought my photon two weeks ago. First print was ok, second fail (my fault with supports), third ok, then I had lot of problems so I decided to do the calibration testing of Sterling...
Plate clean, alligned and calibrated with the paper sheet method, starter the 30 um test and you can see the result in photos ? any suggestion??

翻譯年糕