ATOM 3D Printer Group 造訪社團

PTFE might need to replace after temperature or working environment hurt it.
From my experience , it's usually temperature too high issue. …… 查看更多

As I got a full clogged hotend, i strangled it with some toothsticks.Heating to 200 degree and pulling toothpick out removed muuuch PLA inside it. Sticking it back in with Little force resulted in The fact that a little piece of wood came out in The no …… 查看更多

Joschka - that is a fascinating story for sure. I have a propane torch that has a flame temperature of something like 1500 degrees F, but it would never have occurred to me to try to heat up the hotend to that temperature.

Getting titanium to glow r …… 查看更多

Hey Birk,
Thanks for that compliment. Wrote it at 2AM, totally tired.
Propane Torch was the word I was missing. …… 查看更多

My print did complete and it is excellent. I will post results in a couple of hours. Thanks again for discovering the "Joschka propane torch solution" for fixing clogged hotends.

I understand the idea of using acetone for unclogging ABS jams, and there is a comparable chemi …… 查看更多

Yep, got that one too.
I dunno about acetone how high the risk for cancer is. But THF definitely has one. And its vapors are bad for lungs, eyes, contact for skin is bad. THAT is nasty stuff. Acetone is like a children playground in comparison to THF. …… 查看更多

Joschka - I hear you. My wife started out as a chemist so I am well aware of the risks and dangers of industrial chemicals. I'm not sure I will ever actually try THF - it is scary stuff indeed. Frankly I like your heating approach much better.

Later …… 查看更多

In my experience ATOM printers are very picky with the quality of the PLA, I use to get the nozzle clogged about 1 and a half reel (1.5kg.aprox.) of PLA, I have to open and change the PTFE for a new one. Finally I change to a premium quality PLA (I use …… 查看更多

That is an interesting comment Jose. What I've read is that most all printers are sensitive to the amount of moisture in the filament, adn that all forms of PLA will pick up moisture from the atmosphere over time. One article said not to store PLA fo …… 查看更多

Its difficult to know as all the PLA manufacturers will tell theirs is the best xD.

I use Fillamentum with good results, they are made in Poland or Czech Republic Im not sure now but you can find a "premium" brand in USA, for sure... just try anof course tell us!!! XD

睡覺的時候不要印....

看起來是韌體更新失敗 ~

Are you running Windows 10? There have been many reports of timeouts and other problems with USB/Serial connections in Win10, so if you are running it make sure you have installed all the current updates. My system loads Atom2 firmware OK, so it will work if you have everything up to date.

試著12v電源也開著..看有沒有差別？

沒成功跟電腦連線中途斷掉了？確定port對再試一次？

try another browser, sometimes it's strange on some browser

ok , thanks

我心中的疑惑，膠帶是否不需塗口紅膠?
我上次用膠帶沒黏住我就放著了 ~

我現在只用玻璃，沒用口紅膠也沒用藍色膠帶，但是有開熱床...50度

嘻…我還在學習中，所以沒想到這點，謝謝您的提點，我明天立馬試…

我也沒熱床…

參數？

那是跨橋, 你搞錯了 :P

我是直接用原廠的測試檔。以前用Botfeeder 的白色料印的都很完美。

降溫度吧？

我單純覺得，一樣的參數沒有印的更漂亮，那就不算是我心中理想的線材，因為我不具備Ting大那樣根據線材特性調整參數的技能，簡單說就是想偷懶。

顏色是滿美麗的

溫度降到185度，風扇速度將到20，利用旋鈕提速到120%來提高回抽速度，目前比較可以看了。但是成型有點鬆散的感覺，沒有讓我感到驚艷的地方。

白色那隻料印出來很俐落

少了牽絲，但結屎依舊......

Esun的料，made in China, piece of SHxT!

剛剛從防潮箱拿出放了幾個月的Botfeeder料，一樣原廠G code跑下去印，什麼都沒調，印的就是乾淨俐落！Made in Taiwan.

右邊這種水準才有資格出來混。左邊esun一捲要價850元啊，這種水準？氣炸！

勸世文無誤......

換上ATOM原廠料，也是放了一陣子了，仍然好用！

給了三次機會，不見改善跡象。我已盡力避免做出偏頗的見解，但最後還是大大的失望了。這隻料牽絲沒有比較少，還會在表面產生結塊。就醬。

botfeeder就是OP

botfeeder號稱很純，只有pla與色料

這樣罩住的優點是什麼啊~

http://www.simplyalt.com/atom/viewthread.php?tid=1323

http://www.simplyalt.com/atom/viewthread.php?tid=867

好懷念的版本...

衝了?

等大師先，我跟你借就好

這是CO2燈管雷射吧?少說也有110W以上

這一台應該要破百萬了~

基恩斯 55W的光纖雷雕機，還可以雕曲面以及依據3D Molde 雕刻需要的區域！

神的標準配備

請勿使用鏡面材質(?

好有存在感啊 0.0 (不小心手過去不知道會怎樣 0.o?)

這是？ 月光寶盒？ http://img.131home.com/....../10/21/2009102109493522f.jpg

Mira Alberto Bauer

好殺～～～