ATOM 3D Printer Group 造訪社團

原文網址 施正偉
2016-01-12 07:16:20

3D 列印行業最為火爆的技術叫做立體光刻⋯⋯

原文網址 陳佳卿
2016-01-12 01:34:30

升級完1.99 韌體2.04B z軸校正功能大躍進啊！口紅膠一層就能粘死死。

先po個剛出爐的美女。

防翹曲2mm 溫度175 厚度0.1 速度應該是10mm/s 高度100mm 支架60度間隔0.2mm 30mm左右開啓側風扇。

溫度pid、50x50方框、歸零（0.26）等校正都做過。

耗時6小時多。

收尾一樣還是悲劇一坨⋯⋯誰教教我怎麼救收尾( ´ ▽ ` )ﾉ

到最後一層都在哪轉圈圈加熱⋯⋯

陳佳卿
2016-01-12 01:36:24

http://www.thingiverse.com/thing:105551 (載點)

李穆
2016-01-12 01:40:56

min layer [s] 改 0.2～0.5看看

陳佳卿
2016-01-12 01:44:30

所以這樣只會引響到最後面那層嗎?!
他的設定是指低於min layer時間就會自動加長時間到min layer的設定值嗎?

李穆
2016-01-12 01:46:55

所以走很慢不就溶掉了嗎？

陳佳卿
2016-01-12 01:47:58

對@"@~~(我一直以為是說設定1秒那層最多時間就只能跑一秒 (跑超快這樣))~~

李穆
2016-01-12 01:49:58

是「至少」跑1秒，不然就開prime pillar來分散時間

Robin Hsu
2016-01-12 03:31:01

如果是為了最後 ending 那一點不好看 ...

不然就在旁邊印一根比它高一點的柱子 @@~

Dan Salvador
2016-01-12 04:24:26

Beautiful

廖新弘
2016-01-12 06:19:57

印象中這個可以不用開支撐

陳錦源
2016-01-12 08:16:54

可以請問你韌體升級到哪一版嗎??

Yu Shu Huang
2016-01-12 08:48:32

我也是1.0的升級1.99後真的差很多!

Daniel Cheang
2016-01-12 10:28:26

防俏曲2mm 是什麼

原文網址 Astik Evihan
2016-01-12 00:05:04

just printed with ATOM 2.0 :)

翻譯年糕

Astik Evihan
2016-01-12 00:05:36

Astik Evihan
2016-01-12 00:05:46

原文網址 曾俊維
2016-01-11 23:49:16

尋找外文比較好的人，可以幫我看這把怎麼下載到完整的檔案嗎？

Charlie Ting
2016-01-11 23:57:36

說是目前在作修改，所以暫時移除了。

曾俊維
2016-01-12 00:03:41

喔，好吧，那先來印烏克麗麗好了

原文網址 Joschka Friedl
2016-01-11 22:28:38

Hey guys,

I wanted to connect some LEDs to my Atom printer. But now that I got everything together, I was wondering... where to connect them to the board? I have 12V LEDs and I want to connect four of them.
I planned to cable them all up with some clamps, then bringing one cable to a switch, from there to power supply - the other cable goes directly to power supply. But as Atom has no direct "power supply" where you can directly pull your power from - where to get it? ^^"

Thanks in advance! :)

翻譯年糕

Clarence Lee
2016-01-11 23:26:10

http://reprap.org/mediawiki/images/0/0d/MKS_GEN-PIN.PNG

Joschka Friedl
2016-01-11 23:39:35

So of I See correct - next to redet button are 12v Pins - no other option, right?But there are two fans there and - on top - laser fan?Other options? :/

Clarence Lee
2016-01-11 23:46:39

get power directly from power supply

Joschka Friedl
2016-01-11 23:59:06

So like, just put The cable directly to The AC/IN plug where The cables for power supply go in?Or should I put them on The right ones, which are empty?

Joschka Friedl
2016-01-11 23:59:57

So in This picture, left four screws. Two left ones (power sup) or two right, empty ones?

Harry Cayne
2016-01-12 19:54:28

it would be nice to have them on only while printing and on the printhead, so I am planning to combine it with the power of the heater element , they don't draw to much power anyways, or do they ?

Harry Cayne
2016-01-12 19:58:17

or you can just pull an other wire from the next heater element that way you can turn on while printing, but not sure what do you have to change in the soft , but must be easy

Joschka Friedl
2016-01-12 20:08:35

I got a switch for mine, this is why I want direct power. With this, I can just click the switch and turn it on whenever I need it.
Had a LED on my Heatbed on another Printer and nearly went crazy with that thing always flickering around. When you conn ect it to the Hotend or Heatbed, you'll get that effect too, as the printer powers the Hotend/Heatbed until it reached the temperature, and afterwards just powers it when it loses temperature. You get an on/off/on/off flickering..

Harry Cayne
2016-01-12 21:01:15

right but if you connect to the heatbed terminals without the thermistor it is going to light all the time while the printing lasts then it turns off , but it has to be set in the program to not to wait for the heatbed signal for the printing

Clarence Lee
2016-01-12 21:29:03

The left side is input

Joschka Friedl
2016-01-12 21:33:55

Clarence: So just put it to The input cables? Don't wanna get anything burned ?

Clarence Lee
2016-01-12 21:41:15

just Parallel Circuits, if you know what you are doing.

原文網址 Shi Xinhui
2016-01-11 22:10:34