Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Kevin Blewitt
2020-03-29 02:10:24

Finally, a successful print...

翻譯年糕

Anders Jens Ramm
2020-03-29 02:19:58

Can u share the stl? ?

Chiewata
2020-03-29 02:23:08

this is on my printing list ?

Kevin Blewitt
2020-03-29 02:24:20

Anders Jens Ramm "I am once again asking for the STL"

Its here, I did just the bust: https://www.thingiverse.com/thing:3528140

Chris Kölsch
2020-03-29 02:35:34

thats with primer on? i see no linings....

Kevin Blewitt
2020-03-29 02:43:15

Chris Kölsch yes, it's with GW black primer.

Megan Raynak
2020-03-29 02:48:56

Nice!

Chris Kölsch
2020-03-29 02:49:36

do you have a photo before the primer?

Chris Kölsch
2020-03-29 02:51:28

this one? is it thin or a ticker one?

Kevin Blewitt
2020-03-29 02:58:16

Chris Kölsch before primer.

The GW on is a thicker one compared to their super thin layer ones but otherwise the normal is pretty thin. If that makes sense.

Jeffrey Opel
2020-03-29 03:37:24

nailed it!

Dustin Wiebe
2020-03-29 05:12:44

*muffled shovel noises*

Ahid du Val
2020-03-29 06:48:25

wow

Hoghead Hoffer
2020-03-29 15:14:04

awesome

Stephen Mitchell
2020-03-29 15:32:44

fine choice of a krieger!

Rico Reyna
2020-03-29 22:46:24

I love this model!

Igor Melnyk
2020-03-30 02:52:04

Print in proton ?

Ernest Sandridge Ill
2020-03-30 05:06:05

IS this from Iron Sky?

Kevin Blewitt
2020-03-30 05:09:27

Ernest Sandridge Ill Death Korps of Kreig from Warhammer 40k.

Kevin Blewitt
2020-03-30 05:09:42

Igor Melnyk it's on my Photon with anycubic green.

Óttar Freyr Einarsson
2020-03-30 08:04:48

Stl for shovel?!

Kevin Blewitt
2020-03-30 08:06:13

Óttar Freyr Einarsson like is there one?

原文網址 Kevin Blewitt
2019-12-28 01:07:05

So, I'm on essentially my 5th or 6th unsuccessful print here and I *still* don't know what is going on. I tried two original prints that maybe weren't supported as well, I managed two 25% scale baby yodas, but there were three on the plate, and I managed to test print the new test print that was on the flash drive. That had a couple issues, but it seemed to be plate leveling issues. I have leveled, leveled again, used the Read method, used the paper method, I've shaken my resin, run it under a warm tap, put a heater in the room, I have been putting all miniatures offset at an angle, I hollowed it, auto supported then checked supports, leveled the machine itself (which wasn't off much), cleaned everything multiple times, replaced the FEP film twice... I'm out of options. I did stop this print once to make sure that the base had managed to stick to the plate, because most of my other prints failed because they stuck to the FEP. I'm like a couple failed prints from filling this with tannerite and going to some BLM land. Any other takes on this consistent failure? Normal Photon, firmware 4.0, hollowed and supported in Chitubox, sliced on the anycubic slicer, used my own, better flash drive, checked and rechecked exposures, doing 8 base layers.

翻譯年糕

Terrence Humbert
2019-12-28 01:11:07

Michael Tetreau
2019-12-28 01:12:20

Kevin Blewitt
2019-12-28 01:12:25

Ryan Neal
2019-12-28 01:13:43

Kevin Blewitt
2019-12-28 01:13:47

Michael Tetreau
2019-12-28 01:14:34

Kevin Blewitt
2019-12-28 01:14:35

Terrence Humbert
2019-12-28 01:15:17

Kevin Blewitt
2019-12-28 01:16:30

Kevin Blewitt
2019-12-28 01:18:04

Terrence Humbert
2019-12-28 01:18:37

Michael Tetreau
2019-12-28 01:19:28

Kevin Blewitt
2019-12-28 01:19:36

Kevin Blewitt
2019-12-28 01:20:31

Terrence Humbert
2019-12-28 01:20:48

Ryan Neal
2019-12-28 01:20:59

Kevin Blewitt
2019-12-28 01:21:34

Kevin Blewitt
2019-12-28 01:22:26

Terrence Humbert
2019-12-28 01:23:27

Ryan Neal
2019-12-28 01:23:29

Ryan Neal
2019-12-28 01:24:15

Kevin Blewitt
2019-12-28 01:24:33

Ryan Neal
2019-12-28 01:24:54

Ryan Neal
2019-12-28 01:25:54

Kevin Blewitt
2019-12-28 01:28:07

Stefan Giudici
2019-12-28 01:30:47

Kevin Blewitt
2019-12-28 01:31:44

Stefan Giudici
2019-12-28 01:31:51

Stefan Giudici
2019-12-28 01:32:40

Simon Bramley
2019-12-28 02:27:14

Kevin Blewitt
2019-12-28 02:29:04

Nipuna Gunarathne
2019-12-28 02:34:17

Alex Vee
2019-12-28 04:05:37

Kevin Blewitt
2019-12-28 04:17:54

原文網址 Kevin Blewitt
2019-12-27 11:36:28

When you all print smaller miniatures with integrated bases, do you still angle them on the plate or can you just print with the base adhering to the plate?

翻譯年糕

Joe Brislane
2019-12-27 11:39:22