• #maker+t=market
  • COSPLAY 3D 建模
  • 3D列印服務
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Matt Tilson
2019-09-15 23:46:33

Hey everyone! A while back, I won another of Elegoo's giveaway contests for a set of their new plastic vats with non-replaceable FEP.

I received mine yesterday and although I haven't used it to print yet, I wanted the give everyone a sneak peek for those who haven't seen them or received them yet.

1. There are four to a pack and were packed in nice and tight and sandwiched by two pieces of foam.

2. The vats ship with a plastic protective film over the *bottom* of the FEP. That'll need to come off before printing.

3. The vats ship with very nice plastic lids. These plastic lids are great because they fit the existing vats also (although it is a tighter fit on them).

4. As I feared, they seem to have a slight warp to them, either from the injection molding process or from the tension on the FEP. I don't think it's enough to cause issues with the printing process, though.

5. It fits nicely on the Mars and the Photon, so it can be used across the two. If I had to guess, I would say it probably fits the Epax X1 too.

6. The thought of a disposable plastic vat kinda concerns me a little bit, because that's one more added bit that gets thrown away. I didn't see any marks for recycling, so it may be destined for the dump if you toss it.

7. This may be an awesome way to get cheap vats to quickly change colors/materials, and may lead to some interesting layered color swapping!

8. Thanks for reading and happy printing!

翻譯年糕

Mike Fatchett
2019-09-15 23:50:09

Rick Hanson
2019-09-15 23:50:41

Caleb Custer
2019-09-15 23:51:07

Matt Tilson
2019-09-15 23:51:07

Alex Reasinger
2019-09-15 23:51:28

Vaughan Lundin
2019-09-15 23:52:38

Christoph J. Hannen
2019-09-15 23:53:57

Matt Tilson
2019-09-15 23:56:57

Matt Tilson
2019-09-15 23:57:25

Matt Tilson
2019-09-15 23:58:23

Alex Vee
2019-09-16 00:00:46

Matt Tilson
2019-09-16 00:02:18

袁丞徽
2019-09-16 00:13:29

Sherri Johnson
2019-09-16 00:35:45

Justin Miller
2019-09-16 00:38:00

André Klein
2019-09-16 00:48:05

Matt Tilson
2019-09-16 00:56:24

Matt Tilson
2019-09-16 00:57:28

Douglas Rector
2019-09-16 01:15:38

Matt Tilson
2019-09-16 01:22:37

Florian Helmer
2019-09-16 02:05:00

Doug Bowman
2019-09-16 02:07:00

Justin Cupitt
2019-09-16 02:14:29

Matt Tilson
2019-09-16 02:15:21

Kevin Boogaard
2019-09-16 02:53:17

Douglas Rector
2019-09-16 03:04:41

Mike Syfritt
2019-09-16 03:11:27

Stefan Giudici
2019-09-16 04:52:29

Rodolfo Padilla Ruiz
2019-09-16 04:52:37

Matt Tilson
2019-09-16 05:02:21

Joseph Covington
2019-09-16 06:12:05

Matt Tilson
2019-09-16 06:12:52

Mike Syfritt
2019-09-16 06:15:01

Matt Tilson
2019-09-16 06:15:57

Nicolas Tsagarides
2019-09-16 06:43:03

Vaughan Lundin
2019-09-16 06:45:51

Matt Tilson
2019-09-16 06:48:26

Vaughan Lundin
2019-09-16 06:51:33

Matt Tilson
2019-09-16 09:36:40

Chris Koonce
2019-09-16 09:37:01

Matt Tilson
2019-09-16 09:39:40

Earl McCammon
2019-09-16 11:28:55

Matt Tilson
2019-09-16 11:29:48

Scott Pavlich
2019-09-16 11:48:50

Justin Cupitt
2019-09-16 11:54:28

Tom Sargison
2019-09-16 15:44:59

Michael Lee Wood
2019-09-16 20:07:44

Jared Zadorozny
2019-09-16 22:43:43

Jared Zadorozny
2019-09-16 22:47:19

Nicholas Taylor
2019-09-16 23:21:53

Giancarlo Arriola
2019-09-17 22:08:32

Juan Pablo Bagnon
2019-10-18 19:10:48

Matt Tilson
2019-10-18 20:27:23


原文網址 Matt Tilson
2019-03-31 08:15:12

Looking at the Photonsters github, I saw there is a new firmware listed (same for anycubic official site). The filename looks to be dated 18 Mar 2019. Does anyone have an idea what has changed and whether this is a truly stable firmware update?

翻譯年糕

Pedro Ribeiro Fialho
2019-03-31 10:35:52

Sen Kun
2019-04-01 00:35:13


原文網址 Matt Tilson
2019-03-07 02:59:01

Out of curiosity, has anyone gutted their Photon and modded it with a RaspPi + RAMPS (or other board) and then loaded nanoDLP? I may be oversimplifying quite a bit, but at least in my head it seems like it would be reasonably straightforward to do.

翻譯年糕

Andy Eakin
2019-03-07 03:29:17

Greg Bauer
2019-03-07 05:25:07

Stefan Giudici
2019-03-07 05:54:34


原文網址 Matt Tilson
2019-02-22 12:35:06

Probably nobody cares, but in case someone does - I left a model on the build plate and resin in the vat for 2 months in a blue window version that sits about 6 feet from a window but does not receive direct sunlight.

After 2 months, the model is still OK without post-cure. I was able to easily remove the model from the build-plate. There was still liquid resin on the build-plate, although it was thicker than normal.

The resin in the vat had separated, but had not congealed, skinned, or cured. I was able to stir it back up and get it to mix. The vat was a little low, so I added a little bit of fresh resin from the bottle to the vat and mixed it in good.

I successfully printed a model immediately afterwards.

All this to say - unless your printer is in direct sunlight, you shouldn't have reason to be concerned about resin life in the vat for at least several weeks.

翻譯年糕

Nick Williams
2019-02-22 12:54:41

Nick Santana
2019-02-22 13:16:08

Kevin Delger
2019-02-22 13:21:11

Lucas Milner
2019-02-22 13:47:23

Andy Murtagh
2019-02-22 15:04:19

Nathan Hurst
2019-02-22 15:08:44

Andy Murtagh
2019-02-22 16:04:54

Mathieu Tremblay
2019-02-23 10:38:05

Jordan Baldrige
2019-02-25 10:16:07


原文網址 Matt Tilson
2019-01-07 13:05:29

I got bored tonight while waiting on a print to finish...

翻譯年糕

Aaron Cater
2019-01-07 13:09:24

Jeremy Lauzon
2019-01-07 13:17:15

Chayanin Somton
2019-01-07 14:05:18

Mariano Loisi
2019-01-07 15:36:17

Andrew Lee
2019-01-07 20:38:38

Keith Barnett
2019-01-08 01:10:39

William Charles Chamberlin
2019-01-08 01:16:49

Keith Barnett
2019-01-08 01:17:43

Matt Tilson
2019-01-08 01:44:33

Jonathon Sullivan
2019-01-08 11:23:35

Jonathon Sullivan
2019-01-08 11:24:30


原文網址 Matt Tilson
2018-12-01 14:13:36

What's the minimum temperature the resin can be exposed to during storage/transport?

A friend of mine wants to start resin printing, but he lives in Canada where in the winter it is -40C to 0C on a regular basis. He's concerned that when resin is delivered to his house during the day, it will be ruined by the time he gets home from work because of the cold.

Anyone from The Great White North have experience with extreme cold and resin?

翻譯年糕

Gabriel Brockman
2018-12-02 01:13:26


原文網址 Matt Tilson
2018-11-11 14:38:46

So I forgot to empty my resin tank before vacation, then forgot it was full when I got back from vacation and didn't need to use it for another two weeks. This story doesn't end the way you think it does..

After almost a month of not being used, it printed just fine! ? Dispelling the myth that you HAVE to empty your vat when not using. But it is still a good idea. Don't follow in my footsteps. Lol

翻譯年糕

Rémi Mesnager
2018-11-11 15:25:01

Matt Tilson
2018-11-11 15:30:51

Simon Powell
2018-11-11 15:34:25

Nick Williams
2018-11-11 15:34:26

Matt Tilson
2018-11-11 15:35:24

Simon Powell
2018-11-11 15:36:50

Matt Tilson
2018-11-11 15:37:34

Simon Powell
2018-11-11 15:39:21

Josh Norris
2018-11-11 16:13:20

Simon Powell
2018-11-11 16:21:37

Bronson Ferri
2018-11-11 16:37:59

Matt Tilson
2018-11-11 21:58:31

Josh Norris
2018-11-12 01:11:29

Josh Norris
2018-11-12 01:12:18

Mark Wardle
2018-11-12 01:39:27

Bronson Ferri
2018-11-12 01:47:12

Gabriel Holmes
2018-11-12 09:31:12


原文網址 Matt Tilson
2018-10-03 12:21:15

Any ideas what would cause this to happen during curing after cleaning? I was curing two others just like this at the same time and they both came out fine.

翻譯年糕


原文網址 Matt Tilson
2018-09-30 11:06:52

So I printed a part in two halves with the intention to glue them together. I thought everything was properly supported, I had no errors in Validator, I used like 30% density supports, I thought the angle was good, and by all means the prints look GREAT. Except they warped.... about half of it fits together like a glove, and the other half has like a 2mm gap.. about 10 hours worth of printing down the drain.

Any idea what the hell happened?

翻譯年糕


原文網址 Matt Tilson
2018-09-17 02:11:51

When you hollow a print, do you not have to worry about internal overhangs and unsupported islands? How do you keep things from failing?

翻譯年糕


 

討論主題

全不選 常用關鍵字