• COSPLAY 3D 建模
  • #maker+t=market
  • 3D列印服務
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Daniel Thomson
2019-05-07 22:43:17

So, recently running into issues printing :(

As can be seen, I've had support failure, as well as just general failures.

Any help would be much appreciated.

翻譯年糕

Clinton Hoines
2019-05-07 23:08:14

Hobby Mike
2019-05-07 23:10:57

Daniel Thomson
2019-05-07 23:40:13

Hobby Mike
2019-05-07 23:53:19

Sean Poeschl
2019-05-08 01:08:18

Nick Williams
2019-05-08 01:13:40

Nick Williams
2019-05-08 01:13:53

Nick Williams
2019-05-08 01:14:35

Nick Williams
2019-05-08 01:16:13

Richard Shapiro
2019-05-08 01:53:35

Daniel Thomson
2019-05-08 01:56:01

Daniel Thomson
2019-05-08 01:57:03

Nick Williams
2019-05-08 01:57:59

Nick Williams
2019-05-08 02:04:00

Daniel Thomson
2019-05-08 02:05:02

Daniel Thomson
2019-05-08 02:06:42

Nick Williams
2019-05-08 02:08:24

Daniel Thomson
2019-05-08 02:11:23

Gregorey Savieo
2019-05-08 04:26:49

Nick Williams
2019-05-08 04:30:38

Calvin Tan
2019-05-08 06:00:33

George Wall
2019-05-08 17:32:28

Marnie Jefferson
2019-05-08 18:14:02

Dennis Back
2019-05-08 23:27:20

George Wall
2019-05-08 23:59:33

Dennis Back
2019-05-09 00:12:33

Aaron Swickard
2019-05-09 01:33:03


原文網址 Daniel Thomson
2019-03-01 22:32:34

Question.

Is there a way to 'mirror' a print in the PHOTON's Slicer software?

翻譯年糕

Toby Kirkby
2019-03-01 22:33:43

Nikolas Willingham
2019-03-01 23:27:01

Dillon Olney
2019-03-02 03:35:01

Blaine Tsukayama
2019-03-02 07:58:43

Robb Nunya
2019-03-04 04:19:52


原文網址 Daniel Thomson
2019-01-30 09:46:47

Alright....finished up my first go of Minis!

Now to research to get a better layering cause my next go round will be at 0.01 instead of 0.03 :D

翻譯年糕

Bryan Jolson
2019-01-30 10:31:32

Paul Mabbott
2019-01-30 13:36:39

Paul Mabbott
2019-01-30 13:36:53

Richard Wheeler
2019-01-30 15:33:43

Anthony Pham
2019-01-30 17:40:48

Arnie Locsin
2019-01-30 20:23:21

Daniel Thomson
2019-01-30 21:53:22

Daniel Thomson
2019-01-30 21:53:39

Bryan Jolson
2019-01-30 22:06:29

Arnie Locsin
2019-01-30 22:52:06

Paul Mabbott
2019-01-30 23:30:26

Paul Mabbott
2019-01-30 23:31:00

Paul Mabbott
2019-01-30 23:43:21

Mikko Asikainen
2019-01-30 23:58:50

Arnie Locsin
2019-01-31 00:26:33


原文網址 Daniel Thomson
2019-01-28 06:08:18

So, finished a couple of prints..can't really cure them right now as (THANX VANCOUVER!) the weather has been overcast for the past few days, so...now I am forced to wait on a UV Lamp:

https://www.amazon.ca/…/ref=ppx_yo_dt_b_asin_title_o01__o00…

So, the big question I can't find a lot of answers on is...How long is a standard UV Cure?

翻譯年糕

Tom Howley
2019-01-28 06:10:25

Daniel Thomson
2019-01-28 06:11:25

Marcus Como
2019-01-28 06:14:17

Jack Sweek
2019-01-28 06:21:24

Adam Horton
2019-01-28 11:56:07

Paul Mabbott
2019-01-29 02:37:19

Dave Landry
2019-01-29 04:38:50

Eric Green
2019-01-31 02:15:07


原文網址 Daniel Thomson
2019-01-26 23:28:57

Question:

I just got the Photon, gone through the leveling, hit new 0-Level, but when I then use the HOME button to move the Z-Axis, it is never 'tight' to the bed/paper as when I was leveling. Is this correct? or is the new 0-Level somehow about 1mm above where I said the new 0-level is?

翻譯年糕

Ryan Turner
2019-01-26 23:30:05

Bob Leschyna
2019-01-26 23:36:03

Che Fielding
2019-01-26 23:40:42

Sen Kun
2019-01-26 23:41:19

Sen Kun
2019-01-26 23:43:45

Daniel Thomson
2019-01-26 23:58:42


 

討論主題

全不選 常用關鍵字