Anycubic Photon Printer Owners 造訪社團 » 用戶發文

I just replaced my LCD screen on my original Photon that I’ve had for around a year now. However it doesn’t appear right. Could something else be going on the printer? This is how things currently appear. The first is what I get when I run the exposure test on the printer. The others are what I get when attempting a print.

*Edit* I have double checked the cable and everything seems to be seated correctly. After some further testing it looks at those there is temporary screen burn occurring. If I try the print first and then go to the UV Exposure then the image of the print are intermixed with the test rectangle. Same if the test is run first. Is this a faulty replacement or is the motherboard going?

翻譯年糕

With Anycubic being on holiday till the 1st I'm hoping the community here might have some suggestions. I've been running 4.2.17 for a while now and recently started to experience frame shearing on the right side of the printer thats been getting progressively worse and thicker. I have attempted to upgrade to 4.2.18 (and 4.2.19 even though I've heard it has issues). However when attempting to upgrade and then run the UV check the entire screen just flickers and flashes making it impossible for me to print anything while running those two firmwares.

Has anyone run into this issue and found a way to get around it? I have just been using the left side of my printer at 4.2.17 but have some designs lined up that will require the entire print bed to be used and I don't want to deal with the frame shearing.

Any assistance would be greatly appreciated.

翻譯年糕

I’ve recently started to have some issues with my original Photon. Hoping the collective hive can provide some insight. Recently anything on the right side of the printer is having some errors. No matter how big of a print it is at about the 60% mark a super thin layer forms around the model. This repeated at about 65%-75% and again around the 90%. I’ve had the printer for about a year now. It see regular use but not overt heavy use. I checked the LCD screen and everything seems to be functioning with no issues. Cleaned it off to ensure it doesn’t have anything on it. FEP has been replaced. But the issue persists and it’s only on the right side. Does anyone have any suggestions on what I can do to correct this or what the issue might be?

翻譯年糕

Little smaller then originally intended (didn’t double check my measurements before slicing) but it was a surprisingly quick print and nice detailing.

翻譯年糕

Finished painting my “The Child”. Definitely a great print, came out so clean and so nice looking.

翻譯年糕

Does anyone have some nice settings for Anycubic Transparent Red? I tried the ones on the Google Doc with very little success. I am no being able to get good consistent prints since I received it. I had really good success with the Dental Castable (at least that’s what they labeled it, looked Transparent Green to me) that came with my printer. I’ve tried both settings for the Transparent Red, Dental Castable Green, and Transparent Green.

Any assistance would be appreciated.

翻譯年糕

I picked up a UV light today. I know the Anycubic resin is listed at curing with 405n. The light is 390-400n, will it still work but just take longer? From what I have seen people only place their stuff under a UV light for a couple moments and it’s cured. I have left some stuff under the one I got for several minutes and it doesn’t seem to be doing anything.

QUANS 110V 10W UV Ultra Violet LED Black Light for Curing Glue, Resin Cure 3D Printer, Blacklight, Fishing Aquarium, Party Supplies, Neon Glow in the Dark, With US Plug

翻譯年糕

What is everyones go-to clear resin? And where are you getting it?

I am going to be needing a bottle of resin in the next couple days as I’ve almost gone through the 500ml of dental castable that came with my Photon. I was thinking of getting some clear resin and was just going to stick with Anycubic. But can’t find it on Amazon, the only clear resin I found was Monoprice. From what I’ve heard it yellows a fair bit.

翻譯年糕

This is only my 3rd print with the Photon. What came out came out really great. But for some reason the front face of the models are completely missing. You can see a clean line like they were never even registered to print. Does anyone have a recommendation as to the cause of this?

翻譯年糕

Only my 3rd print into owning my Photon and learned a valuable lesson. Always make sure to double check the build plate is securely fastened before starting a new print. Glad I caught this at only 7% into the print.

翻譯年糕