Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Paul Fagan
2020-01-08 14:46:17

Has anyone in the UK managed to find a source for any reasonably priced flexible resin?

原文網址 Paul Fagan
2019-11-01 05:07:55

If had support fail before, but I've never see anything like this. Anyone able to she some light on what on earth happened?

翻譯年糕

Adrian Carter
2019-11-01 05:09:43

Paul Fagan
2019-11-01 05:11:37

Caio Donini
2019-11-01 05:11:56

Joan FH
2019-11-01 05:13:17

Paul Fagan
2019-11-01 05:14:37

Joan FH
2019-11-01 05:17:15

Vidal Sanchez
2019-11-02 12:22:54

原文網址 Paul Fagan
2019-10-21 00:56:54

Any idea what could cause a support failure in that position? There wouldn't have been any stress on the support at that stage that couodnhavr caused a problem as far as I can see.

翻譯年糕

原文網址 Paul Fagan
2019-10-01 02:40:23

Can anyone recommend a good spectrum analyser app for Android to use when tuning the fep? There seem a be rather a lot that present you with a lot of data that's only visible for a split second and makes no sense to the layman.

翻譯年糕

Travis K. Jansen
2019-10-01 02:44:46

Rose Stumpwater
2019-10-01 02:48:20

Paul Fagan
2019-10-01 02:54:12

Ian Gill
2019-10-01 03:52:31

Jez Clark
2019-10-01 05:41:02

Richard Webb
2019-10-01 05:44:45

Larry Blenn Jr.
2019-10-01 12:25:29

Tobi Altebaeumer
2019-10-01 12:40:59

Tobi Altebaeumer
2019-10-01 12:42:09

Lee Johnson
2019-10-01 13:01:02

Paul Fagan
2019-10-01 14:21:16

Larry Blenn Jr.
2019-10-01 14:25:37

Paul Fagan
2019-10-01 14:27:10

原文網址 Paul Fagan
2019-09-23 03:10:22

Are there any particularly good prints to run for testing a new FEP installation?

翻譯年糕

Steve Ton
2019-09-23 03:28:08

Paul Fagan
2019-09-23 03:29:00

Paul Fagan
2019-09-23 05:57:43

Mike Foreman
2019-09-23 16:55:01

Paul Fagan
2019-09-23 16:58:47

原文網址 Paul Fagan
2019-09-22 04:27:38

Just about to change the FEP out for an Epax non FEP. I haven't been able to find any guides or videos about it. I presume it's the same as installing a FEP, just without the bottle cap?

IE tighten the screws slowly going from opposite to opposite. I take it I can fully tighten all the screws and not worry about getting the frequency of the sound right?

翻譯年糕

Elle Heilig
2019-09-22 04:29:46

Stefan Giudici
2019-09-22 08:36:42

原文網址 Paul Fagan
2019-09-10 05:37:54

Anyone having problems with ChiTuBox 1.5.0 not connecting some of the raft to the build plate? Half of the raft is fine, but for some reason its not connected on this side.

翻譯年糕

Kevin Rank
2019-09-10 05:47:24

James Byer
2019-09-10 05:47:50

James Byer
2019-09-10 05:47:58

Paul Fagan
2019-09-10 05:49:08

Paul Fagan
2019-09-10 05:49:13

Greg Kourakos
2019-09-10 05:53:18

Chad Elstad
2019-09-10 08:09:43

Stephen Brewer
2019-09-10 08:32:09

原文網址 Paul Fagan
2019-08-02 06:36:57

Does anybody know how far the build plate is from the FEP when the Z is homed?

翻譯年糕

Mark Wardle
2019-08-02 12:27:44

Tim Moulton
2019-08-02 12:41:18

Niall Forrester
2019-08-02 17:28:45

Paul Fagan
2019-08-02 17:38:30

Nicolas Tsagarides
2019-08-04 17:19:52

原文網址 Paul Fagan
2019-07-25 05:44:42

Would be grateful if anyone using Anycubic grey would share their exposure settings for 0.05 layer height.

I'm sure it will be suggested, so yes I have tried the resin settings spreadsheet on Google Drive. Although I started off with those settings I found that the normal exposure time of 18 seconds was way to high. I'm working my way through some AmeraLabs calibration files and I'm currently down to a normal exposure of 6 seconds.

Although this does fit a lot better with the suggested exposure times printed on the bottle it does seem rather strange that it's so much lower than those in the spreadsheet.

翻譯年糕

Tim Moulton
2019-07-25 06:07:04

Stefan Giudici
2019-07-25 06:57:52

Paul Fagan
2019-07-25 07:01:53

Björn Ståhlnacke
2019-07-25 13:36:29