• COSPLAY 3D 建模
  • 3D列印服務
  • #maker+t=market
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Jeremy Wilson
2020-03-28 02:41:55

Hi all. I have a print that is going to take about 7 hours. The first time it broke off of the supports and failed. Is there a way to check to see if it’s actually printing about mid way through?

翻譯年糕

Rory Kostman
2020-03-28 02:43:54

press the pause button? It will lift the part up. You may or may not incur some minor layer shifting in the print due to the pause. I've had pretty good luck with my Photon and PAUSE (unlike my Ender 3, which PAUSE might as well be labelled "ruin this print?")

Jeremy Wilson
2020-03-28 02:45:31

Rory Kostman thank you! I was worried about layer shift so that’s why I haven’t tried it. Hate seeing a bunch of broken supports stuck to the plate after all that time overnight.

Simon Wilson
2020-03-28 02:53:42

Have the supports 20mm long, and pause it while they are still printing in the first fifteen minutes, then after that you can see it anyway. You could always set the lifting distance higher (and the lifting speed to make up for it) if you want to get a peek sooner

Jacob Hale
2020-03-28 02:59:58

Just open it and check....Seriously, it will be fine. I do it all the time.

Jeremy Wilson
2020-03-28 03:01:18

Jacob Hale I opened it but it’s sitting in the vat below where I can see. Do you mean hit pause first and open it up?

Stuart Johnson
2020-03-28 06:30:48

Such is the resin way. Us FDMrs, we know within 2 layers if its going to go horribly...but resin? Shes a temptress.

Richard Tyler Jr
2020-03-28 07:55:18

Stuart Johnson yes, she is a fickle goddess but oh so satisfying.

Fred Bey
2020-03-28 08:45:28

You can pause it, and it will raise up enough to see. But you run the risk of getting a layer line where you paused it. Up to you if it's worth it.

Jeremy Wilson
2020-03-28 08:47:46

Thanks for the helpful posts guys! It came out great.


原文網址 Jeremy Wilson
2020-03-10 04:01:57

I'd like to sculpt some straps in ZBrush similar to the ones pictured here and print them. Do you guys know if there a flexible resin that I could try? I don't want to heat up normal resin and bend it because that just sounds like a bad idea all around. Any help would be appreciated. Thanks!

翻譯年糕

Maxime Mathurin
2020-03-10 04:11:06

Adil Muschelewicz
2020-03-10 04:28:36


原文網址 Jeremy Wilson
2019-10-21 23:12:14

Is there a semi-flexible resin that people here really like to use? I’m trying to make weapons for 6” action figures but I’d like for them to have a slight flex to them so they don’t snap in case they get bent while posing them around. Any suggestions?

翻譯年糕

Rigo Arevalo
2019-10-21 23:24:59

Jeremy Wilson
2019-10-21 23:37:34

Rigo Arevalo
2019-10-21 23:41:22

Jeremy Wilson
2019-10-21 23:42:58

Rigo Arevalo
2019-10-22 00:12:32

Jeremy Wilson
2019-10-22 00:13:48


原文網址 Jeremy Wilson
2019-09-01 19:33:41

Anyone have a config setting that always works for them for Chitubox slicer software? I’m printing some small action figure heads and every time I try that program the prints fail. The supports and raft are stuck to the plate but the heads seem to break off. Using AnyCubic gray resin.

翻譯年糕

Florian Helmer
2019-09-01 19:42:22

Jeremy Wilson
2019-09-01 19:43:37


原文網址 Jeremy Wilson
2019-08-20 19:02:43

Does anyone here use their printer to print custom action figure heads? Namely, ones for Marvel Legends figures? If so, is there some secret to getting a neck peg hole in the head that fits most figures so it snaps on nicely? I use ZBrush to create the sculpts, but I just can’t hit the spot with the peg hole. It’s either too large or too small.

翻譯年糕

Luke Mason
2019-08-20 19:50:11

Jeremy Wilson
2019-08-20 20:07:09


原文網址 Jeremy Wilson
2019-03-23 08:56:49

Here’s how the first custom action figure (Snake Eyes from G.I. Joe) came out with the aid of the Photon for printing the head. Body is a kitbashed Marvel Legend but the head is from scratch created in ZBrush. Can’t believe how nicely the print came out. So many possibilities!

翻譯年糕

Nathan Nato Curtis
2019-03-23 14:03:09

Matthew McNair
2019-03-23 14:49:48

Dylan Hancox
2019-03-23 20:34:23

Jeremy Wilson
2019-03-23 20:44:02

Dylan Hancox
2019-03-23 20:46:12

Ed Del Rey
2019-03-24 07:53:32

Jeremy Wilson
2019-03-24 07:58:08

Ed Del Rey
2019-03-24 08:06:30

Ed Del Rey
2019-03-24 08:07:57

Jeremy Wilson
2019-03-24 08:13:01

Ed Del Rey
2019-03-24 08:20:01

Jeremy Wilson
2019-03-24 08:20:30

Ed Del Rey
2019-03-24 08:21:31


原文網址 Jeremy Wilson
2019-03-20 11:45:03

First failed print with the new Photon. Bummer. Left it running to find the supports stuck to the plate and thin hard pieces stuck to the bottom of the vat. Guess I’ll clean it all out and re-level tomorrow. Good excuse to try a new resin I guess!

翻譯年糕


原文網址 Jeremy Wilson
2019-03-19 20:04:36

Anyone here airbrushing their primer on? Any recommendations? I was thinking of picking up either the black or gray (or both) Vallejo surface primers today. Thanks!

翻譯年糕

Martin Lawrence
2019-03-19 20:08:14

Vladimir Strycek
2019-03-19 20:08:43

Michael Earley
2019-03-19 20:10:55

Tom Smith
2019-03-19 20:11:56

Justin Brink
2019-03-19 20:14:24

Dani Rose
2019-03-19 20:15:13

Chris Sutherland
2019-03-19 20:28:49

Marvin Tomizzi
2019-03-19 20:47:08

Rob Mayberry
2019-03-19 20:52:18

Justin Brink
2019-03-19 20:52:58

Savio Ku
2019-03-19 21:13:00

Nick Thompson
2019-03-19 21:27:11

Michael Barfus
2019-03-19 21:55:33

Dani Rose
2019-03-19 22:10:09

Nick Thompson
2019-03-19 22:12:59

Jeremy Wilson
2019-03-19 22:17:44

Keith Barnett
2019-03-19 22:49:56

Keith Barnett
2019-03-19 23:04:26

Peter Teal
2019-03-19 23:52:49

Jeremy Wilson
2019-03-20 00:02:58

Michael Van Kesteren
2019-03-20 00:16:03

Peter Teal
2019-03-20 02:02:51

Benjamin Matthews
2019-03-20 02:57:28

Michael Van Kesteren
2019-03-20 03:14:36

Jeremy Wilson
2019-03-20 03:28:18

Peter Teal
2019-03-20 03:42:34

Peter Teal
2019-03-20 03:44:14

Peter Teal
2019-03-20 03:45:42

Michael Van Kesteren
2019-03-20 04:14:59

Robert Fliege
2019-03-20 07:27:38

Robert Fliege
2019-03-20 07:29:21

Justin Ragsdale
2019-03-22 23:55:03


原文網址 Jeremy Wilson
2019-03-17 21:33:45

Hi everyone! New to the group. New Photon is arriving today and I'm pretty excited! Just have a quick question. I'm going to be using this to create toys and was wondering if I can prime and paint directly on the resin after post-processing (curing, sanding, etc.) I'll be starting with a couple of custom action figure heads I created in ZBrush.

Coming from FDM printing, there is always a ton of time with cleanup and then casting silicone molds and further refining. If I could skip a few of those steps it would be awesome. This seems like a great group! Thanks in advance!

翻譯年糕

Sen Kun
2019-03-17 21:38:33

Dylan Hancox
2019-03-17 21:38:45

Jeremy Wilson
2019-03-17 21:47:27

Dylan Hancox
2019-03-17 22:00:55

Jeremy Wilson
2019-03-17 22:05:20

Dylan Hancox
2019-03-17 22:09:14

Jeremy Wilson
2019-03-17 22:15:19

Sean Poeschl
2019-03-17 23:10:10

Jeremy Wilson
2019-03-17 23:50:29

Matt Paul
2019-03-18 02:02:56

Jeremy Wilson
2019-03-18 02:05:29

Sean Poeschl
2019-03-18 03:05:24

Dani Rose
2019-03-18 05:19:38

Jeremy Wilson
2019-03-18 05:31:36

Jeremy Wilson
2019-03-18 11:39:54

Sean Poeschl
2019-03-18 11:59:52

Sébastien Guilbaud
2019-03-18 18:23:57

Jeremy Wilson
2019-03-18 18:25:41

Dylan Hancox
2019-03-18 18:53:28

Sean Poeschl
2019-03-18 19:57:10

Jeremy Wilson
2019-03-18 21:54:00

Sébastien Guilbaud
2019-03-18 21:57:25

Jeremy Wilson
2019-03-18 22:01:06

Dylan Hancox
2019-03-19 00:19:13

Jeremy Wilson
2019-03-19 00:27:04


 

討論主題

全不選 常用關鍵字