Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Sagar Bhatnagar
2019-08-18 08:41:22

Hi all,

Looking for some help. I've been printing for some time, but recently ran into a whole bunch of failed prints. Reinstalled my FEP, tightened it up to match the frequency that Youtube videos told me too... and started printing again.

However, I've had consistently failed prints, and not sure what's going on. I recently tried to print some little cars, but only 4/6 printed. The prints consistently adhere to the FEP.

Looking for any advice!

Thanks in advance.

Edit: Chitubox error was showing that I had not connected to build plate, was not the case :) reloaded and everything was level

翻譯年糕

Vinicius Silva
2019-08-18 08:44:51

Chris Marshall
2019-08-18 08:52:59

Sagar Bhatnagar
2019-08-18 08:53:22

Sagar Bhatnagar
2019-08-18 08:59:09

Sagar Bhatnagar
2019-08-18 08:59:24

Vinicius Silva
2019-08-18 08:59:59

Mike Fatchett
2019-08-18 09:01:57

Sagar Bhatnagar
2019-08-18 09:03:27

Sagar Bhatnagar
2019-08-18 09:04:19

Mike Fatchett
2019-08-18 09:05:06

Vinicius Silva
2019-08-18 09:13:08

Vinicius Silva
2019-08-18 09:14:05

Sagar Bhatnagar
2019-08-18 09:22:49

Sagar Bhatnagar
2019-08-18 09:23:17

Vinicius Silva
2019-08-18 09:29:10

Sagar Bhatnagar
2019-08-18 09:29:46

Spike Walker
2019-08-18 16:53:44

Spike Walker
2019-08-18 16:58:50

Sagar Bhatnagar
2019-08-18 22:09:50

Sagar Bhatnagar
2019-08-18 22:09:59

原文網址 Sagar Bhatnagar
2019-04-01 07:13:11

Hi all,

Okay back with some actual data. I’m not sure why my prints are stretching, would anyone be able to give me some advice ?

I haven’t changed an base settings.

Layer thickness: 0.02
Normal exposure: 10
Off time: 6.5
Bottom exposure: 85
Bottom layers: 20

It’s happening to all my prints.

Any help would be greatly appreciated !

翻譯年糕

Job Moolenaars
2019-04-01 07:19:16

Milton Maxson
2019-04-01 07:22:05

Adam Horton
2019-04-01 08:20:56

Sagar Bhatnagar
2019-04-01 10:12:55

Markus Schönfelder
2019-04-01 13:49:20

Sen Kun
2019-04-01 14:36:46

Sagar Bhatnagar
2019-04-02 04:56:43

原文網址 Sagar Bhatnagar
2019-03-31 11:13:28

Hi all, I'm experiencing significant shrinkage and stretching on my printed models. Any idea what generally causes these?

翻譯年糕

Nick Williams
2019-03-31 11:27:08

Rasmus Josephsen
2019-03-31 11:32:10

Stefan Giudici
2019-03-31 11:37:40

Markus Schönfelder
2019-03-31 18:17:03

原文網址 Sagar Bhatnagar
2019-03-31 03:38:36

Hi everyone, back with another question. I finally got everything to adhere to the build plate, but another problem arose. Supports lost adhesion to the models at some point.

Not enough supports? I've attached some photos of the problem and stl's below.

Specifications:
Layer Thickness: 0.025
Normal Exposure Time: 8
Off Time: 2
Bottom Exposure Time: 105
Bottom Layers: 8

Resin: Anycubic

翻譯年糕

Zena Andreou
2019-03-31 03:44:00

Sagar Bhatnagar
2019-03-31 03:52:43

Zena Andreou
2019-03-31 03:55:44

Sagar Bhatnagar
2019-03-31 03:56:41

Zena Andreou
2019-03-31 03:58:21

Mark Wardle
2019-03-31 04:09:09

Markus Schönfelder
2019-03-31 04:30:41

Kevin Boogaard
2019-03-31 06:22:41

Kevin Boogaard
2019-03-31 06:24:29

Stefan Giudici
2019-03-31 07:23:57

Sagar Bhatnagar
2019-03-31 07:39:25

Kevin Boogaard
2019-03-31 15:30:08

Sagar Bhatnagar
2019-04-02 05:49:04

原文網址 Sagar Bhatnagar
2019-03-27 02:14:54

Hi all, I’ve recently experienced a number of failed prints and was not sure what’s going on. It seems that either the print is adhering to the plastic screen in the resin tank, or the supports aren’t gripping the print bed. I’ve attached a photo below.

I've added how my supports look as well.

The bases are there but nothing else prints. Any tips?

My specifications are:
Layer Thickness: 0.025
Normal Exposure Time: 11
Off time: 3
Bottom Exposure Time: 85
Bottom Layers: 8

翻譯年糕