Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 杨希震
2019-12-28 09:17:05

Done. Some of the supports merge with the body - strangely- but ok as I can cut them off.
How do people get rid of supports inside?

翻譯年糕

John Chrapkowski
2019-12-28 09:22:48

John Baran
2019-12-28 09:35:55

Jeremy Babcock
2019-12-28 09:41:18

Fred Bey
2019-12-28 09:44:37

原文網址 杨希震
2019-12-27 17:38:07

Did 2 Bulldogs print at one go.
Not sure what happened but the good print has part of his foot missing - lack of support?
The other print split into 2 when I remove supports. Poor layer adhesion?

翻譯年糕

Vincent Balmont
2019-12-27 17:56:47

原文網址 杨希震
2019-12-26 08:32:25

Would you say that 4 is the best?

翻譯年糕

Vernie G-graphy
2019-12-26 09:57:22

Romek Łakomiak
2019-12-26 17:42:03

El Moreno de Cosio
2019-12-26 17:51:58

Zena Andreou
2019-12-26 17:59:23

原文網址 杨希震
2019-12-26 07:36:22

Going for my 1st own design print. Is it a norm for it to have so much supports?? I used light but heavy is worst!

翻譯年糕

Ryan Pennington
2019-12-26 07:40:38

Paul Carter
2019-12-26 07:42:11

Lucas Riley
2019-12-26 07:46:01

Bill Abrams
2019-12-26 07:49:37

Lucas Riley
2019-12-26 07:50:23

Brian T Patterson
2019-12-26 07:50:39

Bill Abrams
2019-12-26 07:57:04

Scott Pavlich
2019-12-26 08:32:26

Michael Steadham
2019-12-26 08:56:10

Michael Steadham
2019-12-26 08:56:46

杨希震
2019-12-26 09:07:45

Michael Steadham
2019-12-26 09:08:35

Ramiro Montes De Oca
2019-12-26 09:23:27

杨希震
2019-12-26 09:32:52

Tom Chandler
2019-12-26 10:08:47

Luke Mason
2019-12-26 10:15:50

Matt Stone
2019-12-26 10:20:06

Steven Ngo
2019-12-26 10:27:37

Michael Steadham
2019-12-26 10:57:40

Michael Steadham
2019-12-26 10:58:37

杨希震
2019-12-26 12:13:25

Robert Small
2019-12-26 13:06:53

Marcin Jażdżewski
2019-12-26 17:32:59

Mike Wheway
2019-12-26 21:01:43

Reed Culver
2019-12-27 04:48:33

Neil Joseph
2019-12-27 06:27:53

James March
2019-12-29 14:34:12

原文網址 杨希震
2019-12-25 08:20:51

Successful 1st print I assume.... just my clumsy hands trying too hard to pull it off... :(

By the way, how often do people need to zero the Z? And is it a must to clean all out before the next print?
Thanks and Merry Christmas:)

翻譯年糕

Brian Gabriel
2019-12-25 08:22:43

Timmy Mate
2019-12-25 08:22:47

杨希震
2019-12-25 08:25:03

James Cachia-Garrett
2019-12-25 08:26:10

Scott Schwoppe
2019-12-25 08:26:20

Brian Gabriel
2019-12-25 08:27:31

Joe Guillemette
2019-12-25 09:08:53

Jarin Udom
2019-12-25 17:10:45

Jarin Udom
2019-12-25 17:13:00

Gary Priest
2019-12-27 06:53:50

原文網址 杨希震
2019-12-24 17:46:48

Just arrived....
The thumb drive did not come with the nice cube test print but instead the exposure test only. Hmmm. Where do I get that cube test print that everyone uses?

翻譯年糕