Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Benjamin Matthew Harding
2020-03-29 03:16:31

EDIT: my LCD screen is probably failing. After the classic "turning off and back on again" made the UV test actually show. So we'll see if that will actually work for now. I've had the printer for like 3.5 months now.
I'm having some problems for the first time since I bought it
I'm using Anycubic gray, 90 secs with 6 base layers, and 6 seconds normal exposure time. I'll get a job done, and then the next job fails.
Does there need to be a cool down time between jobs? Inside the printer was a bit warm.
I did have to reset the z=0 once because for some reason it wasn't going all the way down. I hope something isn't wrong with my printer.
I've had several jobs within the past couple days end up like the picture below.

翻譯年糕

Bill Griffin
2020-03-29 03:22:07

Lol, I thought it was cheese

Chris Crute
2020-03-29 03:23:13

I had something similar and what I discovered was that a job would complete but then the next would fail because of resin left on the fep from the successful one. Not 100% cured but enough to make it fail.

Turned out the LCD was failing and was Curing a 'shadow' on the fep between layers when it should have been dark.

Changed the screen and it was fixed, improvement in print quality too!

Benjamin Matthew Harding
2020-03-29 03:28:02

That might be it. I've also emptied the vat and the fep looked fine. This is the exposure test

Benjamin Matthew Harding
2020-03-29 03:31:27

I think my screen failed. I turned it off and back on again and then it was acting normal...? That's so weird

Chris Crute
2020-03-29 03:34:01

Benjamin Matthew Harding mine looked fine on the exposure test but it was clesrly letting UV through when it shouldn't have.

Benjamin Matthew Harding
2020-03-29 03:37:33

Hmmm.. what's weird for me is it wasn't doing any uv light and then after turning it off and back on, it showed up again. If this doesn't print then I'll have to get a new screen for sure

Chris Crute
2020-03-29 03:39:53

If your screen is old (mine was 14 months old with no dead areas) you may be best doing it anyway, the improvement in print quality very noticeable!

Benjamin Matthew Harding
2020-03-29 03:41:05

It's only 3.5 months old, as I got it for a Christmas gift for myself.

Chris Crute
2020-03-29 03:42:16

Hmmmm, there is no saying how long each one lasts. I've heard of people having them degrade in that time though. I was just lucky.

Benjamin Matthew Harding
2020-03-29 03:42:57

Dang. Well thanks for your advice. We'll see what happens

Chris Crute
2020-03-29 03:44:47

Benjamin Matthew Harding Good luck,

原文網址 Benjamin Matthew Harding
2020-02-03 03:43:09

Hi everyone. I'm loving the quality of prints I get, and it's great being able to use it for D&D minis. I'm trying to get more quality from them by lowering the layer height shown on the Google sheet. I'm using anycubic gray and black mostly, but I also have the default translucent green and clear.

翻譯年糕

Benjamin Matthew Harding
2020-02-05 07:45:57

原文網址 Benjamin Matthew Harding
2020-01-14 05:34:03

Hey everybody, what are some small space ways to keep your printer isolated and insulated? I'm trying to keep the smell to a minimum and keep everything at a good temperature Hey everybody, what are some small space ways to keep your printer isolated and insulated? I'm trying to keep the smell to a minimum and keep everything at a good temperature 翻譯年糕

Jason Jacobs
2020-01-14 05:37:04