Anycubic Photon Printer Owners 造訪社團

原文網址 Cristian Cozma
2019-11-21 14:00:31

Hi, as solution to temperature problem, if we heat the printing bed, would not be ok? Using heat pads glued on upper side, it will take some time to heat all that metal but is also the piece that makes contact with the resin.

翻譯年糕

Rose Stumpwater
2019-11-21 14:09:18

Zena Andreou
2019-11-21 14:15:32

Cristian Cozma
2019-11-21 14:24:13

Stefan Giudici
2019-11-21 16:07:06

Rose Stumpwater
2019-11-21 16:11:22

Petr Osipov
2019-11-21 22:30:22

原文網址 Daniel Funposter
2019-11-21 13:57:31

Took a chance on a big print and was very happy!

Note: anyone have a solution to "pitting" that happens when I pull away supports? Half the time my models have holes in them or small pillars sticking from them

翻譯年糕

Tom Inglis
2019-11-21 13:59:27

Dane Bennett
2019-11-21 14:01:16

Mark Rayner
2019-11-21 14:03:36

Jendrik Witt
2019-11-21 14:04:56

Jendrik Witt
2019-11-21 14:05:43

Jarin Udom
2019-11-21 14:05:47

Zac Bolton
2019-11-21 14:37:23

Nicholas Taylor
2019-11-21 14:54:16

Ben Hodgkinson
2019-11-21 15:19:53

Arthur Erbricht
2019-11-21 16:10:12

Daniel Nollen
2019-11-21 16:15:42

Nicholas Smith
2019-11-21 16:26:46

Regan Fairbanks
2019-11-21 17:09:27

Scott Weldon
2019-11-21 18:46:21

Stephen Polito
2019-11-21 19:49:40

Doug Bowman
2019-11-21 20:11:58

Doug Bowman
2019-11-21 20:14:54

Eric Green
2019-11-21 21:22:46

Stephen Polito
2019-11-21 21:57:19

Stephen Boulton
2019-11-22 00:14:03

Mike Roof
2019-11-22 02:19:02

Dustin Wiebe
2019-11-22 08:58:41

Jerry Little
2019-11-22 10:26:10

原文網址 Dan Santee
2019-11-21 12:39:16

My daedric armor print with knowledge from this group. Thanks to everyone for all the guidance! Such an amazing group of people.

翻譯年糕

Jarrod Smith
2019-11-21 14:16:31

Eric Weber
2019-11-21 16:57:57

原文網址 Alexis Canizalez
2019-11-21 12:36:15

Hi all, i have a question i read that Anycubic sold new photon version that is named Fauxton not the clasicc then my question is the next... if my printer have 5.5 fimware then is the new Fauxton? I bought in October promos 翻譯年糕

Karel Svoboda
2019-11-21 12:39:12

Alexis Canizalez
2019-11-21 12:47:40

Karel Svoboda
2019-11-21 12:49:46

Jan Pfriender
2019-11-22 03:24:46

Karel Svoboda
2019-11-22 05:15:01

Karel Svoboda
2019-11-22 05:21:08

原文網址 Andrew Springer
2019-11-21 12:29:01

Not sure if this is the best place to ask but what kind of different propertys can be achieved with different resins? Like for example is there a resin that's flexible after curing? Or maybe extra strong?

TLDR: My clumsy ass dropped my precious mini and his legs snapped off ?

翻譯年糕

Tim Moulton
2019-11-21 12:35:11

Stephen Lewis
2019-11-21 12:48:38

Jarin Udom
2019-11-21 12:57:09

Andrew Springer
2019-11-21 12:57:49

Andrew Springer
2019-11-21 12:58:00

Sen Kun
2019-11-21 14:34:47

Stephen Lewis
2019-11-21 14:53:38

Andrew Springer
2019-11-21 14:54:52

Jon Carroll
2019-11-21 15:01:50

Stephen Lewis
2019-11-21 15:20:42

David Collinson
2019-11-21 19:19:00

Andrew Springer
2019-11-21 19:23:49

David Collinson
2019-11-21 19:27:55

Andrew Springer
2019-11-21 19:30:53

Gustavo Enriquez
2019-11-22 00:25:34

Shawn O'Hara
2019-11-22 14:11:52

原文網址 Karel Svoboda
2019-11-21 12:13:40

Kyr’bes or Mandalorian mythosaur skull, Anycubic grey, ~5cm height. AA Lvl 4 in chitubox

翻譯年糕

Karel Svoboda
2019-11-24 08:42:52

原文網址 Cliff Goodwin
2019-11-21 11:47:25

Hey Group!

When running the Resin XP Finder test...do you guys cure it under your UV lamp? if so for how long?

翻譯年糕

Andriy Lutsenko
2019-11-21 12:38:04

Cliff Goodwin
2019-11-21 12:50:49

Andriy Lutsenko
2019-11-21 12:59:54

Felipe Carascosa Ferro
2019-11-21 13:05:30

Mono MonochromeAgent
2019-11-21 15:40:32

Bob Deblier
2019-11-21 15:48:32

Mono MonochromeAgent
2019-11-21 15:53:24

原文網址 Ricky Cokely
2019-11-21 11:36:12

Help! I recently replaced my LCD and began a print that started off fine with no noise. I left the room and when I came back suddenly my printer started making this strange sound. It sounds like a fan but I'm not sure. Anyone know what this could be?

翻譯年糕