Anycubic Photon Printer Owners 造訪社團

原文網址 Sandro Montecchiani
2019-08-04 23:50:15

To be or not to be....... this is the question !

Some personal thoughts on the Photon and how to push it to the limits….

So I’m looking for a complete workflow with the goal to get the best dimensional accuracy using Photon for printing dental model.

So the main purpouse is “dimensional accuracy”

I decided to use dental resins that have a lower shrinkage if compared to generic resin. I'm testing Anycubic Dental Skin and another resin from an Italian Producer. The Z resolution chosed was 50 um, a good value for dental models.

First of all: Run Resin Exp Finder from Photonsters. This is the starting point.

It gives me a range of exposure time, min & max, and a sweet spot (even if I have some difficulty reading it..)

Once found the range of exposure, the next step is to perform other tests to validate and fine tune the exposure time.

I used for this porpouse the NestaCube file: it gives me two types of information, the first about fit (the smaller cube into the bigger): here I can modify exp time to have the best fit between the parts:

This test get us dimensional information too: i can measure the bigger cube dimensions to see if they correspond to the nominal;

And here I have the first doubt: is it more correct to adjust first the fit to have the best, and last measure the dimensions, and if needed act on scaling the model ?

Another solution could be first measure the dimensions and adjust time exposure to have correct dimensions, and then looking at the fitting and correct this if needed by an x-y dimensional compensation. The Go-NoGo Gauge test is my preferred tool for this.. (but we do not have horizontal compensation in Photon slicer and neither in ChiTuBox…. and voxelOps is a little complicated to install and use..)) ?

What is the PhotonMasters thought?

翻譯年糕

原文網址 Mike Warren
2019-08-04 23:34:01

I tried to level using the Flint Read Method but it appears my bar is hitting the vat tray. I saw online I could use washers to give it more space. What size are the washers?? Or is there another thing I could try?

翻譯年糕

Scott Pritchard
2019-08-04 23:54:26

Mike Warren
2019-08-05 00:07:14

Caleb Custer
2019-08-07 00:25:12

Mike Warren
2019-08-07 00:26:17

原文網址 Jamie Osborne
2019-08-04 23:10:00

The AnyCubic resin bottle has changed, now come with a child safe lock and an inner seal, which has helped in this occasion because the bottle was damaged in transit.

See photos

翻譯年糕

William Riker
2019-08-05 03:28:27

Jamie Osborne
2019-08-05 03:42:07

Lorenzo Di Sante
2019-08-05 03:44:41

原文網址 John Baran
2019-08-04 22:59:58

I purchased a Photon about 10 days ago, absolutely love it. After using a CR-10 for 2 years this thing blows it out of the water with the detail.

I noticed the Photon S is an upgraded model, my question is - I'm still within my return/exchange window with Amazon, is it worth the $120 difference it would cost me to exchange it for the Photon S?

翻譯年糕

Mark Wardle
2019-08-04 23:02:55

Mike Hoogstraat
2019-08-04 23:07:43

Ofek Samsonov
2019-08-04 23:10:55

Martin Svedenblad
2019-08-04 23:35:54

Sen Kun
2019-08-04 23:38:07

Stefan Giudici
2019-08-04 23:49:55

Derek Reihe
2019-08-05 00:00:26

Jon Carroll
2019-08-05 00:04:01

Kevin Boogaard
2019-08-05 00:43:24

Ofek Samsonov
2019-08-05 00:48:01

Ofek Samsonov
2019-08-05 00:50:32

Martin Svedenblad
2019-08-05 00:51:53

Derek Reihe
2019-08-05 00:57:05

Sen Kun
2019-08-05 01:15:43

Andrew Gott
2019-08-05 01:54:36

Scott Clark
2019-08-05 02:21:09

原文網址 Ric Watts
2019-08-04 22:48:58

A newbie question but why do larger objects with a significantly sized flat area to print directly on the bed always pull away while orienting then away from the bed works. Should I never print directly in the bed with no supports?

Why would a larger surface area be detrimental? Sorry coming from FDM printing and it’s a bit counter intuitive?

翻譯年糕

Chayanin Somton
2019-08-04 22:50:45

Simon Powell
2019-08-04 23:00:01

Ric Watts
2019-08-04 23:02:48

Ric Watts
2019-08-04 23:03:09

Melecio Guzman
2019-08-07 00:48:25

原文網址 Nigel White
2019-08-04 22:28:04

Has anyone tried one of these filters ?

翻譯年糕

Allan Johansen
2019-08-04 22:33:39

Hosung Kim
2019-08-04 22:40:01

Michael Martin
2019-08-05 19:41:22

原文網址 Chad Hoverter
2019-08-04 22:16:07

whats this red mean on the underside of the model in the Chitubox setup??

翻譯年糕

Chad Elstad
2019-08-04 22:16:46

Chad Hoverter
2019-08-04 22:17:22

Wayne Rogers
2019-08-04 22:18:21

Wayne Rogers
2019-08-04 22:20:03

John Popson
2019-08-04 22:24:12

Chad Hoverter
2019-08-04 22:24:31

Chad Hoverter
2019-08-04 22:24:46

Chad Hoverter
2019-08-04 22:25:53

John Popson
2019-08-04 22:26:24

Chad Hoverter
2019-08-04 22:27:38

Lorenzo Di Sante
2019-08-04 22:27:43

John Popson
2019-08-04 22:30:37

Chad Hoverter
2019-08-04 22:32:17

Chad Hoverter
2019-08-04 22:32:43

John Popson
2019-08-04 22:32:53

Chad Hoverter
2019-08-04 22:33:33

John Popson
2019-08-04 22:33:36

Ric Watts
2019-08-04 22:39:26

Ric Watts
2019-08-04 22:39:58

Nathanael Gardner
2019-08-04 22:40:00

Wayne Rogers
2019-08-04 22:40:06

Wayne Rogers
2019-08-04 22:41:35

Kameron Michael Beal
2019-08-04 22:44:01

John Baran
2019-08-04 22:44:16

Nathanael Gardner
2019-08-04 22:46:04

Nicolas Tsagarides
2019-08-04 22:50:37

Nathanael Gardner
2019-08-04 23:03:55

Chad Hoverter
2019-08-04 23:04:34

Chad Hoverter
2019-08-04 23:08:34

Chad Hoverter
2019-08-04 23:09:08

Wayne Rogers
2019-08-04 23:10:04

Chad Hoverter
2019-08-04 23:11:26

Chad Hoverter
2019-08-04 23:12:14

Wayne Rogers
2019-08-04 23:12:57

Alessandro Rsx
2019-08-04 23:15:53

Wayne Rogers
2019-08-04 23:16:58

Wayne Rogers
2019-08-04 23:18:50

John Popson
2019-08-04 23:26:52

Chad Hoverter
2019-08-04 23:26:52

James Bricknell
2019-08-04 23:33:11

Chad Elstad
2019-08-05 00:11:58

Jeremy Gilbert
2019-08-05 01:26:59

Chad Hoverter
2019-08-05 02:42:34

Chad Hoverter
2019-08-05 02:42:51

Wayne Rogers
2019-08-05 04:38:30

Chad Hoverter
2019-08-05 05:07:49

Wayne Rogers
2019-08-05 05:18:51

原文網址 Terry Andrews Jr.
2019-08-04 20:45:35

Based on my tests I have now 100% ruled out two things as possible causes of my printing problems. 1. Warped built Plate, measured and within 0.001" 2. Outside UV light causing the large resin "Skin" forming on the FEP, covered all printer Windows with heavy (65LB) Black Card stock to render the chamber 100% immune from both visible and UV outside light sources...... Moving on from those as possible print error factors.

翻譯年糕

原文網址 Susan Sioux Mercer
2019-08-04 20:40:46