Anycubic Photon Printer Owners 造訪社團

原文網址 Michael Fairall
2019-01-11 15:19:34

G'day all. Could someone tell me if I can print this as is or do I need to scale it down so that the supports are within the print area? Will printing like this have any affect on the model or will it simply crop the supports?

翻譯年糕

Robert Silvers
2019-01-11 15:20:19

Michael Fairall
2019-01-11 15:21:45

James Cachia-Garrett
2019-01-11 15:22:13

Zena Andreou
2019-01-11 16:26:05

原文網址 Kyle Ross
2019-01-11 15:13:53

What can cause this? Im not at home so cant get any more details

翻譯年糕

Jake Antonovitch
2019-01-11 15:16:15

Robert Silvers
2019-01-11 15:20:52

Mark G. Gerwig
2019-01-11 15:22:20

Sebastian Andres
2019-01-11 16:35:42

原文網址 Ravi Kumar
2019-01-11 15:01:24

Hello everyone, yesterday I tried a chess piece with halo but after printing liquid resin struk inside the pieces how to overcome this challenge

翻譯年糕

Stefan Giudici
2019-01-11 15:24:46

原文網址 Duncan Nodarse
2019-01-11 14:57:14

After multiple attempts to get the new Anycubic green resin to work, I have come up empty handed. The only successful print I had with the new resin was at 50 microns. When I first got the resin, I tried using it with the original print settings at 20 microns, however it failed to print properly. After asking around, I used the information I got to tweak the settings to hopefully make the print finally come out perfectly at 20 microns. Even after that, only the door and chair printed out. Just to make sure that my bed wasn't unlevel, I immediately cleaned the FEP and print bed and started the same print with the older Anycubic green resin at 20 microns with the original settings. Sure enough, it printed out perfectly. I recommend that you stay away from the new Anycubic green resin based on my experience, at least until people have had enough time to experiment with it and find the right exposure settings. I will be replacing the newer green resin with the Anycibic grey resin.

翻譯年糕

Robert Silvers
2019-01-11 15:07:25

Sen Kun
2019-01-11 15:10:25

Duncan Nodarse
2019-01-11 23:21:45

Duncan Nodarse
2019-01-12 01:50:21

Robert Silvers
2019-01-12 01:59:18

原文網址 Trevor Kennemer
2019-01-11 13:30:51

So I have a stupid question. I'm printing an electric violin and it's going to be hollow with 6mm thick walls. When I go to post cure it in my UV chamber, will the UV light be able to permeate all the way through the 6mm walls to fully cure ALL of the resin?

翻譯年糕

Mark Wardle
2019-01-11 14:03:30

Trevor Kennemer
2019-01-11 19:16:01

原文網址 Kevin Kelley
2019-01-11 13:12:55

Okay... Ordering my photon tomorrow! Last thing I'd like some advice on. My back room is now occupied due to family, so my only option is the room next to my bedroom, which is connected by a gap in the wall. I'm mostly worried about my cat and dog breathing in too much of the smell... Should I be concerned? And any suggestions to keep the smell out for my critters?

翻譯年糕

Alexander Taylor
2019-01-11 13:14:10

Kevin Rank
2019-01-11 13:49:32

Kevin Kelley
2019-01-11 13:53:52

Alexander Taylor
2019-01-11 13:55:40

Alexander Taylor
2019-01-11 13:56:59

Kevin Kelley
2019-01-11 13:57:28

Alexander Taylor
2019-01-11 13:58:17

Kevin Kelley
2019-01-11 13:58:27

Alexander Taylor
2019-01-11 13:59:49

Kevin Kelley
2019-01-11 14:00:42

Kevin Kelley
2019-01-11 14:01:58

Alexander Taylor
2019-01-11 14:04:27

Kevin Kelley
2019-01-11 14:06:07

Alexander Taylor
2019-01-11 14:06:40

Kevin Kelley
2019-01-11 14:07:16

Kevin Kelley
2019-01-11 14:08:07

Chris Ainsworth
2019-01-11 14:26:02

Robert Silvers
2019-01-11 15:13:12

Chris Ainsworth
2019-01-11 15:14:47

Robert Silvers
2019-01-11 15:17:09

David Nicholls
2019-01-11 18:53:46

陳彦廷
2019-01-11 18:56:35

Bernie Horowitz
2019-01-11 22:12:02

Kevin Kelley
2019-01-12 00:14:45

Ben Johnson
2019-01-12 01:25:55

Kevin Kelley
2019-01-12 02:21:56

原文網址 Zac Morris
2019-01-11 12:55:52

The temporary apartment workspace post Hurr. Michael. Nothing like I had but happy to finally have a desk again. I finally got a new bottle of black resin leading to a few more matchbox/hotwheels prints.

翻譯年糕

原文網址 Robert Silvers
2019-01-11 12:47:04

Is a resin high-temp enough to print a filament drive for a FDM printer? I don't think they get very hot. But it sits on the stepper motor so gets a little hot.

翻譯年糕

Matt Tilson
2019-01-11 13:18:57