• COSPLAY 3D 建模
  • 3D列印服務
  • #maker+t=market
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 T.R. Griffith
2020-03-16 11:24:45

So I've seen several posts about holes in the FEP. How do they get there and is there a way to avoid them?

翻譯年糕

Yasser Hamed
2020-03-16 11:26:27

I think mostly when a print fails and there are some small cured resin pieces left in the vat. The next time the plate comes down, it pushes against the cured resin and makes the hole. So I'd say just make sure your vat is clear of bad or cured resin pieces

Stephen Colin Richie
2020-03-16 11:27:42

The film is under a lot of stress from the suction. It will eventually wear out. It can also be caused by debris in the vat or on the build plate. Or a poorly handled tool.

Sam Griffiths
2020-03-16 11:31:12

Dented my FEP in the first week when cleaning it out, didn't have it on a hard surface so pressing down caused damage. No holes yet but came close

Scott Pavlich
2020-03-16 11:59:07

Debris. It’s the main reason that happens: either broken (failed) bits or tiny pieces left stuck to the build plate that people miss: keeping your resin and plate clean are critical

Fred Bey
2020-03-16 12:38:27

Bad prints, unsupported islands that break free.

It's good to check between prints for random debris.

If you see a leak, change the FEP even if you don't see a hole. The hole may only show up while flexing, and will blow out next time you print and make a BIG mess.

Neal Conway
2020-03-16 14:46:13

Same. Had a raft stick to it and when I removed it the damn stuff had dented. Did the water test and all was well so onward and upward!

Phez Darryn Stanmore
2020-03-17 04:16:08

I once put a hole in the vat area of the FEP, while poking holes for the screws lol. I was a little cheeky and covered it with a bit of tape and printed around it ha haaa


原文網址 T.R. Griffith
2020-03-13 02:00:56

So I bought a non-heated ultrasonic cleaner and filled with 99% IPA. A week later and it's crumbling apart. What successful cleaning devices do you all use? Besides a toothbrush and Mean Green. I know about those, I would like to stick the 99% IPA, it does a great job. I just need something reliable to put it in.

翻譯年糕

Zena Andreou
2020-03-13 02:03:26

T.R. Griffith
2020-03-13 02:06:40

Joe Kirkus
2020-03-13 02:09:39

Adam Bishop
2020-03-13 02:11:20

Cody Cody
2020-03-13 02:19:01

David Kane
2020-03-13 02:37:37

Jim Nelson
2020-03-13 02:45:04

Tim Parks
2020-03-13 02:54:02

Christopher Fugate
2020-03-13 03:10:18

John Driggers
2020-03-13 03:16:26

Stefan Giudici
2020-03-13 03:19:37

Gaz Aspinall
2020-03-13 03:24:26

Gary Houser
2020-03-13 03:47:51

Neil Perry
2020-03-13 03:51:07

Michael Hockenbarger
2020-03-13 04:11:53

Romulo Favalli
2020-03-13 04:41:58

William Preston Welch
2020-03-13 05:07:24

Christopher Fugate
2020-03-13 05:14:57

Scott Pavlich
2020-03-13 05:36:40

Tim Parks
2020-03-13 05:57:42

Tim Parks
2020-03-13 05:59:06

Tim Parks
2020-03-13 06:00:09

Adam Zed
2020-03-13 06:27:00

T.R. Griffith
2020-03-13 11:38:13

T.R. Griffith
2020-03-13 11:43:18

Adam Zed
2020-03-13 12:00:27

T.R. Griffith
2020-03-13 12:01:32

Nipuna Gunarathne
2020-03-13 18:42:22

T.R. Griffith
2020-03-13 22:01:29

T.R. Griffith
2020-03-13 22:01:31

Ray Sears
2020-03-13 22:13:45

Cody Cody
2020-03-13 22:14:33

Adam Zed
2020-03-14 04:42:14


原文網址 T.R. Griffith
2020-03-12 04:42:01

I loaded a photon file with 7 minis on it into the Photon File Validator 30 minutes ago and it just says 'loading file', should I be concerned?

翻譯年糕

Warren Peace
2020-03-12 04:43:41

Ben James Couey
2020-03-12 04:54:13

T.R. Griffith
2020-03-12 04:56:56

Ben James Couey
2020-03-12 04:57:21

T.R. Griffith
2020-03-12 04:57:27

T.R. Griffith
2020-03-12 04:59:45

Warren Peace
2020-03-12 05:01:13

T.R. Griffith
2020-03-12 05:01:37

Ben James Couey
2020-03-12 05:29:33

T.R. Griffith
2020-03-12 05:31:43

Ben James Couey
2020-03-12 05:50:13

T.R. Griffith
2020-03-12 05:58:30


原文網址 T.R. Griffith
2020-03-09 09:54:24

I've go to make some prototypes for a mass produced product idea and they are supposed to be specific colors. Has anyone tried the Monocure 3D CMYK Pigment Set and if so what is the result? Link in reply

翻譯年糕

T.R. Griffith
2020-03-09 09:54:33

Scott Pavlich
2020-03-09 09:55:46

Damo Cramp
2020-03-09 09:56:00


原文網址 T.R. Griffith
2020-03-07 23:32:14

So here's my process, can you tell me if I'm on the right path? Prepare model in Fusion 360 with minor tweaks (models from HeroForge or other places) save as STL. Open in PrusaSlice, auto orient so faces are up. Auto support at 75%. Export w/ supports. Open in ChitUBox and slice. Open in Photon File Validator, fix any issues, if island to big go back to PrusaSlice and adjust as needed. GoTo 3, if not GoTo 5. Put .photon file on good USB and plug into Photon. Print. WAAAIIIITTTT Detach plate, scrape off printed object into ultrasonic jewelry cleaner filled with IPA and set for 3 minutes, Run HOT water over printed object and remove supports. LIGHTLY sand leftover support bumps Place under UV light and rotating stand for 5 minutes (+/- depending on size) Finish (paint if needed, varnish, whatever) Collect Underpants
Profit 翻譯年糕

Kees van Dongen
2020-03-07 23:37:17

Fred Bey
2020-03-07 23:42:18

Donovan Lever
2020-03-07 23:51:13

Tim Parks
2020-03-08 00:08:40

Dan Andersson
2020-03-08 00:19:31

T.R. Griffith
2020-03-08 00:52:02

Dan Andersson
2020-03-08 00:56:17

Richard Shapiro
2020-03-08 05:11:03

T.R. Griffith
2020-03-08 05:24:25

T.R. Griffith
2020-03-08 06:45:46

Stefan Giudici
2020-03-08 13:38:37

T.R. Griffith
2020-03-08 13:48:44

Stefan Giudici
2020-03-08 13:52:05

Dan Andersson
2020-03-08 14:16:21

Neil Ramsay
2020-03-08 22:49:44


原文網址 T.R. Griffith
2020-03-07 23:05:54

First real print. Elegoo Standard Grey at 13 seconds /.05mm layer. I still need to sand away the support nubs but I'm very pleased with the results.

翻譯年糕

Tim Parks
2020-03-08 04:08:02

Kold Nguyen
2020-03-08 04:10:32

T.R. Griffith
2020-03-08 04:26:48

Jacob Palmer
2020-03-08 05:51:04

T.R. Griffith
2020-03-08 06:44:12

Jacob Palmer
2020-03-08 07:10:50

T.R. Griffith
2020-03-08 10:49:57

T.R. Griffith
2020-03-08 10:51:11

T.R. Griffith
2020-03-08 10:51:54


原文網址 T.R. Griffith
2020-03-07 03:34:31

Any advice on using the Photon File Validator? It shows several unsupported islands, I do the Fix and it shows a half dozen where it states nothing can be done. BTW, NEWB is clearly stamped on my forehead.

翻譯年糕

Michael Martin
2020-03-07 03:44:20

T.R. Griffith
2020-03-07 04:33:27

Michael Martin
2020-03-07 04:47:13

Dan Andersson
2020-03-08 14:47:40

Sen Kun
2020-03-08 18:30:58


 

討論主題

全不選 常用關鍵字