Anycubic Photon Printer Owners 造訪社團

原文網址 Brian Corbin
2019-10-30 04:11:35

I'm changing my FEP for the first time tonight. I'm pretty confident in the process, but I'm wondering...

So, the official Anycubic FEP is .15 mm. The FEP I ordered is .20 mm. Should I re-level, or is it going to be ok? Thanks!

翻譯年糕

Ryan Myers
2019-10-30 04:12:38

Christian Plösser
2019-10-30 04:22:44

Scott Pavlich
2019-10-30 04:38:55

David Collinson
2019-10-30 04:43:43

Brian Corbin
2019-10-30 04:44:16

DJ Brookshire
2019-10-30 04:46:24

Mike Fair
2019-10-30 04:59:12

Hector Alvarez
2019-10-30 04:59:33

Fred Bey
2019-10-30 06:59:50

Stefan Giudici
2019-10-30 13:56:54

Stefan Giudici
2019-10-30 13:57:10

Stefan Giudici
2019-10-30 13:58:56

Kelly Filgo
2019-10-30 19:37:29

原文網址 Doug Holverson
2019-10-30 04:09:45

Is there anything like a brim setting in ChiTuBox? Or are brims more of a filament print thing?

翻譯年糕

原文網址 George Yusupov
2019-10-30 04:01:12

What are these strange stripes between layers? Produced by old photon (white) and new photon S (grey).
How to get rid of them? Looks like a driver glitch, or slicer mistake.....
Every "stair" duplicates previous layer.

Everything is perfectly calibrated, there are no backlash anywhere. Axis revised recently.
90⁰ prints perfectly, without wobbling

翻譯年糕

Sen Kun
2019-10-30 04:07:23

Mothy Reynolds
2019-10-30 04:15:55

George Yusupov
2019-10-30 04:18:15

George Yusupov
2019-10-30 04:19:02

André Nettermann
2019-10-30 04:22:54

Doug Bowman
2019-10-30 04:29:58

Doug Bowman
2019-10-30 04:33:54

Mothy Reynolds
2019-10-30 04:38:32

Doug Bowman
2019-10-30 04:40:31

Doug Bowman
2019-10-30 04:41:20

Mario Hippmann
2019-10-30 05:25:13

Sander Gerits
2019-10-30 05:42:45

Doug Bowman
2019-10-30 05:47:17

Sander Gerits
2019-10-30 05:47:55

Daniel Feeney
2019-10-30 05:57:22

Daniel Feeney
2019-10-30 05:57:32

Doug Bowman
2019-10-30 05:58:37

Serghei Socolov
2019-10-30 07:07:21

Evan Miller
2019-10-30 10:48:34

Mohammad Jdeed
2019-10-30 11:34:23

Ammar Darwish
2019-10-30 13:29:32

Alexander Petrov
2019-10-30 15:30:58

原文網址 Thomas Goncalves
2019-10-30 03:36:26

When the peoples realise the original Photon is now a vintage thing

翻譯年糕

Thomas Goncalves
2019-10-30 03:39:58

Ante Ravlić
2019-10-30 05:56:56

DJ Brookshire
2019-10-30 06:51:32

Tiernan Messmer
2019-10-30 07:28:13

Joel Mendoza
2019-10-30 10:51:35

TC Cramer
2019-10-30 11:41:07

Scott Findlater
2019-10-30 12:26:48

Tiernan Messmer
2019-10-30 12:27:40

Scott Findlater
2019-10-30 12:28:23

Tiernan Messmer
2019-10-30 12:29:38

Scott Findlater
2019-10-30 12:32:25

Gary Houser
2019-10-31 03:53:26

原文網址 Patrick Beals
2019-10-30 03:22:33

I finished a print, removed the parts and then promptly walked outside into the sunlight carrying the residue covered build plate. Thankfully it scraped right off, but that was dumb. ?

翻譯年糕

Sean Secretan
2019-10-30 03:26:55

Smith Hayward
2019-10-30 03:27:18

Alex Vee
2019-10-30 03:27:53

Nicholas Storms
2019-10-30 04:09:26

Matt Reed
2019-10-30 07:33:03

Karel Svoboda
2019-10-30 13:51:13

May FS Kabindong
2019-10-30 14:30:56

Sam Chappell
2019-11-01 06:43:42

Robert Hamberger
2019-11-04 18:13:09

原文網址 Chris LaRose
2019-10-30 03:15:07

What types of things should I be looking at for fails like This. I bought a new vat so I can print terrain with the old beat up one detailed minis with the new one. Both are tuned. this is what I seem to get out of the new one while my old beat-up one prints great. I can barely hear the peeling off the old one while the new one was putting a lot of force on this model. Regardless I'd seen feels like this before and I'm not sure what causes it. I can see we're the peeling force made some of the heavy supports on the base fail. But I don't see any of the actual model failing to cause the sheets of resin to cure on the FEP. This is a very thin model I'm not sure if I just needed to support it more, I printed very thick and heavy models not being hollow and had less issues with peeling Force then with something this size.

翻譯年糕