Anycubic Photon Printer Owners 造訪社團

原文網址 Benjamin Oppenheimer
2019-07-29 13:46:05

New fep made a huge difference

翻譯年糕

Pico Elgin
2019-07-29 21:26:03

Michael S Dooley
2019-07-29 21:58:30

William David Cunningham
2019-07-30 00:03:34

Keif Davies
2019-07-30 02:04:25

William David Cunningham
2019-07-30 02:05:47

Mia Cox-Landeros
2019-07-30 06:10:14

Dave Corbett
2019-07-30 06:46:01

原文網址 Gregorey Savieo
2019-07-29 13:29:05

She had individual hairs.....and it printed them.....

翻譯年糕

Lorenzo JB Saponetta
2019-07-30 10:51:42

Gregorey Savieo
2019-07-30 11:59:56

原文網址 Andrew Mills
2019-07-29 13:08:05

I find smoothing low-poly models to be kind of relaxing. Anyone else agree?

翻譯年糕

Alex Hines
2019-07-29 13:10:45

Adam Foster
2019-07-29 13:12:03

Erik Osmera
2019-07-29 13:16:48

Andrew Mills
2019-07-29 13:19:01

Ike O'Ohiocaigh
2019-07-29 15:58:09

Aaron Marino-Drake
2019-07-30 00:26:13

Mark Wardle
2019-07-30 05:12:32

Andrew Mills
2019-07-30 10:31:45

Andrew Mills
2019-07-30 10:33:31

Mark Wardle
2019-07-30 10:42:44

Andrew Mills
2019-07-30 10:44:54

原文網址 Robert Small
2019-07-29 11:59:46

!!!!???? Anycubic contacted me about my broken cable.....I just might get this Photon back on the program! HOOORAAYYY!!!!

翻譯年糕

Susan Sioux Mercer
2019-07-29 13:59:08

Steve Nottingham
2019-07-29 19:01:22

Robert Small
2019-07-29 21:01:24

原文網址 Richard Zeinner
2019-07-29 11:50:38

Ready to crush some goblin skulls.

翻譯年糕

原文網址 Clint Primley
2019-07-29 11:48:44

Ursus minimus. From a scan of a sculpture of a grizzly in Vancouver.

The model can be found here - https://www.thingiverse.com/thing:3777117
The sculpture can be found here - http://kenclarke.yolasite.com/grizzly.php

翻譯年糕

Kyle Calderwood
2019-07-29 13:35:03

Clint Primley
2019-07-30 05:12:43

原文網址 Seona van der Pol
2019-07-29 11:44:23

I'm having an issue with my prints (monocure rapid grey) sticking TOO well to the plate. I broke my spatula, and have had to resort to a craft knife blade to remove the prints and even then I still have bits sticking that I have to scrape off. I haven't sanded, I use a drop of platebond because I've had trouble in the past with the print separating from the plate, and I'm printing outside, overnight in Australia when temps are getting as low as 8-9 degrees celsius. I thought resin had to be heated in winter or it wouldn't work? Any ideas? Especially if anyone has found a safe alternative to a craft blade without potentially amputating their fingers! I tried a metal paint scraper but it's not sharp enough to get under the edge of the print.

翻譯年糕

Stefan Giudici
2019-07-29 11:50:23

Mike Fatchett
2019-07-29 11:50:31

Seona van der Pol
2019-07-29 11:52:32

Scott Pavlich
2019-07-29 11:55:45

Seona van der Pol
2019-07-29 12:13:56

Adam Nock
2019-07-29 12:19:35

Rigo Arevalo
2019-07-29 12:27:34

Jarrod Smith
2019-07-29 20:54:57

Seona van der Pol
2019-07-29 21:15:14

原文網址 Clifford Schwankner
2019-07-29 11:18:51

Its already getting better and faster... check this out!

A follow up to another post i made a few weeks ago...

Insane fast... imagine this in a few years...

翻譯年糕

Phil Davidson
2019-07-29 11:35:43

Bruce Barton
2019-07-29 13:47:03

Michael Van Kesteren
2019-07-29 14:17:15

Arthur Withier
2019-07-29 18:39:48

Neil Ramsay
2019-07-29 19:32:19

Clifford Schwankner
2019-07-29 20:08:15

Neil Ramsay
2019-07-29 20:09:49

Jerry Baldwin
2019-07-30 03:28:48

原文網址 Mike Fatchett
2019-07-29 11:01:49

First run with Ele gray and Tenacious. Love it. The bows can be flexed. I cut one in half by accident. Only issue is that they are about 10 percent too big. I forgot to scale them down to 25mm. Whoops! They will be fine though. I just poured the Tenacious in with what I had in the vat so I have no clue what the proportion is. I would guess 30/40 percent Tenacious.

翻譯年糕