Anycubic Photon Printer Owners 造訪社團

原文網址 Dmitri Shevchenko
2019-04-03 16:45:27

One of our models available in the starter kit on our Patreon =)

+ photo coloring from our subscriber

翻譯年糕

Dmitri Shevchenko
2019-04-03 16:54:46

原文網址 Dan Smith
2019-04-03 16:11:01

Supports failed by the rest of the print is better than its ever printed before.. interesting...

翻譯年糕

Silas Bo Nielsen
2019-04-03 16:19:19

Dan Smith
2019-04-03 16:19:47

Silas Bo Nielsen
2019-04-03 16:29:26

Dan Smith
2019-04-03 17:02:50

Dan Smith
2019-04-03 17:03:42

原文網址 Martina Ginevra Albano
2019-04-03 15:23:54

Flint Read method of levelling has permitted me to get my very first print with grey resin ❤️

翻譯年糕

Jamie Joules
2019-04-03 16:28:26

Eric Wilfreesboro
2019-04-03 23:26:38

Harry 'Skip' Baker
2019-04-04 10:59:16

原文網址 Dada Man
2019-04-03 15:03:30

Hey guys I need some advice... I just changed my resin to the black one. I did a print but only my very small items printed but the rest is sitting on the fep. I’m printing at 0.02 I tried the settings online and the default settings just at 0.02 both have the same issues. Should I re level the bed and try again?

翻譯年糕

Susan Sioux Mercer
2019-04-03 15:27:06

原文網址 Ken Lim
2019-04-03 14:29:40

Any success with alternatives to FEP for Vat film? I tried 3 kinds of PET film, 2 thicknesses of 0.1 & .127mm. It is optically much more transparent than FEP so I thought it might allow lower exposure times. It’s also much harder & scratch-proof than FEP. All good, right? However, I found that its stiffness greatly increases peel-force & end up with many failed prints & split models with some parts on BP & some in vat. I tried loosening it down to 250Hz tightness [compared to 300-350Hz for FEP] but that caused vat to leaked after 2 prints. So unless I can find Optical PET film thinner than 100microns, I’m done experimenting with it. I have some Epax “non-FEP on order to try out.

翻譯年糕

Muhammad Zulkhairol Yacob
2019-04-03 14:39:37

Guti Gutmann
2019-04-03 15:18:34

Dan Jay
2019-11-13 02:26:39

原文網址 Jethro Pugh
2019-04-03 13:59:16

Seem to be having an ongoing issue where after moving from a larger surface area to a smaller area the print drifts heavily to one side for a few layers then straightens up again the part that is the same shape as the red line should be straight the whole way up, this was printed flat but at 45 the same issue seems to occur just in different places. Any thoughts on the cause?

翻譯年糕

Susan Sioux Mercer
2019-04-03 15:25:56

Richard Humble
2019-04-03 18:25:15

Savio Ku
2019-04-04 16:58:59

Jethro Pugh
2019-04-04 17:17:59

原文網址 Maxwell Silver
2019-04-03 13:36:54

I need some help from the hivemind. I cannot figure out why this print is failing. It produces a pancake on the print bed and a pancake on the FEP sheet. Pictures of the slice and settings attached. I have updated my firmware using the files from the Anycubic site. I am using the original photon (not S) with Anycubic Green resin. Thanks in advance!

翻譯年糕

Dave Smith
2019-04-03 13:43:58

Alex Varley
2019-04-03 15:40:44

Savio Ku
2019-04-03 17:01:03

Zoltán Hári
2019-04-03 17:36:02

Guajolote Messias
2019-04-03 19:05:19

Richard Shapiro
2019-04-03 21:12:11

Beat Grendelmeier
2019-04-03 21:40:54

Nel Elson
2019-04-04 04:03:28

Flint Read
2019-04-04 13:54:10

Maxwell Silver
2019-04-04 14:08:04

Christian Plösser
2019-04-04 20:14:58

Richard Shapiro
2019-04-04 22:22:40

Richard Shapiro
2019-04-04 22:22:48

Maxwell Silver
2019-04-04 23:30:23

Christian Plösser
2019-04-05 00:38:30

Maxwell Silver
2019-04-05 01:11:15

Maxwell Silver
2019-04-05 08:44:23

Maxwell Silver
2019-04-06 08:53:53

Eric Wilfreesboro
2019-04-06 08:55:06

Maxwell Silver
2019-04-06 08:56:17

原文網址 Chad Talford
2019-04-03 12:36:56

So thanks to you all im getting 100 percent bed adherence!...now i get prints that just stop between 50 and 90 percent complete...

翻譯年糕

Dan Smith
2019-04-03 12:45:38

Robert Small
2019-04-03 12:55:29

Chad Talford
2019-04-03 12:55:52

Sean O'Hayer
2019-04-03 13:09:08

Ivan Antharon Antalec
2019-04-03 13:49:04

Dustin Scott
2019-04-03 21:39:38

原文網址 Efrain J. Perez
2019-04-03 12:30:42

Does anyone know where to buy the motherboard for the Photon, according to support is the problem on mine but I can't find it on offical stores.

翻譯年糕

原文網址 Nicholas Bowles
2019-04-03 12:22:08

Those that use monocure clear with pigments, how much does exposure time vary after adding pigments? I'm guessing that the more opaque the resin the higher the exposure time but could that be eyeballed semi accurately?

翻譯年糕

Dan Smith
2019-04-03 12:43:09

Stefan Giudici
2019-04-03 12:47:03