Anycubic Photon Printer Owners 造訪社團

原文網址 Richard Wilson
2019-03-27 11:04:17

Richard Wilson
2019-03-27 11:05:40

Richard Wilson
2019-03-27 11:05:48

Richard Shapiro
2019-03-27 11:09:27

Richard Wilson
2019-03-27 11:51:16

Michael Tennent
2019-03-28 03:48:57

原文網址 Simon Stedman Ingerson
2019-03-27 10:39:25

Second attempt, ever.

翻譯年糕

Jay Thomas
2019-03-27 10:44:17

Benjamin Oppenheimer
2019-03-27 10:45:09

Simon Stedman Ingerson
2019-03-27 18:03:02

Jay Thomas
2019-03-28 00:11:04

原文網址 Aníbal Arriagada
2019-03-27 10:20:36

Hey everyone, I need some help with this stuff, I just got my printer last week and managed to get some prints, although all of the last ones made didn't went further than their base as seen in the picture.
I've tried leveling with two methods, lengthen the first layers exposure times and even placed the printer near the heater to increase outside temperature to 20°C, I don't want to sand the base plate if I don't need to, can someone help me with some usefull tip please? :(

翻譯年糕

Sean O'Hayer
2019-03-27 10:46:12

Zena Andreou
2019-03-27 20:51:40

Aníbal Arriagada
2019-03-28 21:52:54

原文網址 Vinicius Silva
2019-03-27 09:44:07

Photon Light Mask Creator is working, now i need to figure out how to use it and what grey values are acceptable limits.

翻譯年糕

Vinicius Silva
2019-03-27 09:45:56

Rick Ferguson
2019-03-27 10:00:30

Luke Mason
2019-03-27 10:11:29

Eric Wilfreesboro
2019-03-27 10:30:17

Nick Williams
2019-03-27 12:58:34

Luke Mason
2019-03-27 14:03:11

Sen Kun
2019-03-27 14:50:11

Sen Kun
2019-03-27 14:50:56

César Fernández
2019-03-27 14:51:03

Nicolas Poussin
2019-03-27 16:08:36

Nick Wells
2019-03-27 17:32:45

Vinicius Silva
2019-03-27 17:48:55

Vinicius Silva
2019-03-27 17:52:20

Nick Wells
2019-03-27 17:57:08

Nicolas Poussin
2019-03-27 18:05:37

Vinicius Silva
2019-03-27 18:27:01

Vinicius Silva
2019-03-27 19:08:39

Vinicius Silva
2019-03-27 19:14:18

Silas Bo Nielsen
2019-03-28 01:01:51

Sen Kun
2019-04-02 02:24:17

Robert Silvers
2019-04-04 13:05:50

Vinicius Silva
2019-04-04 17:28:46

Maurice Sand
2019-05-25 03:27:58

Sen Kun
2019-05-25 18:49:35

Jarrod Smith
2019-06-22 05:32:17

Jörg Schötz
2019-06-27 00:11:07

Péter Farsang
2019-10-08 03:21:33

César Fernández
2019-10-09 13:51:26

Péter Farsang
2019-10-09 16:29:57

原文網址 Andrew McKay
2019-03-27 09:44:02

So a little update on yesterday’s post about warping: It seems that warping isn’t actually the issue. It’s more like accumulated resin on the top surfaces (closest to the build plate) of the model. The surface in the first pic is supposed to be flat and sharp, but instead it’s lumpy and gross. Anyone have this issue with flat surfaces close to the build plate? What do I do to correct it? And how is it even happening to start with, because the rest of the model is fine...

翻譯年糕