Anycubic Photon Printer Owners 造訪社團

原文網址 Matt Noblett
2019-02-23 02:22:32

Anyone have thoughts and successful settings for AC Skin resin at low layer heights... I've been using orange but looking at the skin color - very nice look. I have grey to use once I run out of Orange... just like to try more options. I realize I can use the spreadsheet, I also do the calibration for the timing of the layers. Just looking for thoughts.

翻譯年糕

Erik Kaski
2019-02-23 02:34:18

原文網址 David Chambers
2019-02-23 02:10:53

WIP on Zelda test print https://www.facebook.com/238088680200901/posts/291325361543899/

翻譯年糕

原文網址 Chris Caudwell
2019-02-23 02:07:07

I've had a couple of prints fail on me recently with nothing at all on the buildplate or stuck to the FEP, basically no resin curing at all. I ran the UV test after each failed print and no pattern/mask shows. If I switch the printer off and on again each time, so far, the problem has gone away. Has anyone else experienced this intermittent problem and if so is there a fix? Could my screen be on the way out or is this more likely a firmware problem?

翻譯年糕

Guti Gutmann
2019-02-23 18:45:51

原文網址 Seth Seth Dyte Dyte
2019-02-23 01:32:48

Got me a little 2b ayyyy no spoilers I still haven’t beaten it.

翻譯年糕

Alex Crisp
2019-02-23 23:15:37

Giancarlo Arriola
2019-02-23 23:58:36

原文網址 Mario Reinh
2019-02-23 01:22:16

Rob Elwell
2019-02-23 08:55:29

Mario Reinh
2019-02-23 15:09:46

Mario Reinh
2019-02-23 15:14:38

Mario Reinh
2019-02-23 15:15:14

Mario Reinh
2019-02-23 15:25:26

原文網址 Dave Smith
2019-02-23 01:04:54

I just got the anycubic photon yesterday I'm very impressed with it so far. I took a shot in the dark leveling it assuming I would have to try a few times. I think I nailed it right off.

翻譯年糕

原文網址 Steve Rawley
2019-02-23 01:01:24

Garret Bertrand For your holiday deer, did you print them standing on their feet with no additional supports added? Also, what are your print settings for the Harz Red?

翻譯年糕

Steve Rawley
2019-02-23 01:02:02

Garret Bertrand
2019-02-23 02:17:01

原文網址 Gareth Jones
2019-02-23 01:00:15

After a little help, been printing fine for a few weeks now. All of a sudden I have had a print fail, cleaned up beefed up supports and tried again still no luck.
I've levelled my bed tightened my FEP and its still failing.

I thought maybe its time to change the FEP but I've only used about 2L of resin and I've read people doing way more than that plus Interestingly the failure on the FEP is the full size of the screen like its exposing the whole bed, then the grip is too much for the plate?

Any ideas? bad file maybe?

翻譯年糕

Zena Andreou
2019-02-23 01:04:43

Philippe Maegerman
2019-02-23 01:08:30

Richard Shapiro
2019-02-23 01:53:20

Zena Andreou
2019-02-23 01:56:13

Eric Green
2019-02-23 01:57:10

Gareth Jones
2019-02-23 01:57:59

Gareth Jones
2019-02-23 01:58:55

Eric Green
2019-02-23 01:59:01

Gareth Jones
2019-02-23 02:00:15

Eric Green
2019-02-23 02:02:40

Gareth Jones
2019-02-23 03:05:43

Zena Andreou
2019-02-23 03:18:51

Gareth Jones
2019-02-23 03:25:30

Zena Andreou
2019-02-23 03:27:01

Gareth Jones
2019-02-23 03:28:06

Eric Green
2019-02-23 03:33:57

Gareth Jones
2019-02-23 03:52:27

Gareth Jones
2019-02-23 04:57:23

Zena Andreou
2019-02-23 04:58:18

Ivan Antharon Antalec
2019-02-25 16:15:32

Gareth Jones
2019-02-25 18:23:58

原文網址 Daniel Barrios-O'Neill
2019-02-23 00:47:42

Folks, does a material safety data sheet exist for the Anycubic resin? I need to do risk assessments to use my printer at work :(

翻譯年糕

Dustin Skye
2019-02-23 01:26:24

Daniel Barrios-O'Neill
2019-02-23 01:33:43

原文網址 Christopher Ashworth
2019-02-23 00:32:25

What is everyone's least favourite resin... which one will you never buy again because you have had nothing but bad experience. What is everyone's least favourite resin... which one will you never buy again because you have had nothing but bad experience. 翻譯年糕

Gabriele Mastrogiovanni
2019-02-23 00:57:17