Anycubic Photon Printer Owners 造訪社團

原文網址 John Wilhelm
2019-01-26 02:10:33

Actually a great print if only those little holes weren't there. Are those air-bubbles? What can be done to prevent this? Thanks for any help.

翻譯年糕

Isamu Shinozaki
2019-01-26 02:14:09

Felipe Martinez
2019-01-26 02:16:50

Stephen Butt
2019-01-26 02:18:36

Fred Breton
2019-01-26 02:20:24

Patrick Smith
2019-01-26 02:22:14

Vinicius Silva
2019-01-26 02:39:11

Mikko T. Pyykönen
2019-01-26 02:40:07

Dominic Goff
2019-01-26 03:06:47

Robert Maefs
2019-01-26 03:09:33

Joshua Jourdan
2019-01-26 03:32:48

John Wilhelm
2019-01-26 04:59:24

Dominic Goff
2019-01-26 05:20:27

Marcus Como
2019-01-26 05:28:50

John Wilhelm
2019-01-26 06:35:35

John Wilhelm
2019-01-26 06:36:05

Reb O'Rourke
2019-01-26 06:36:23

Robert Maefs
2019-01-26 06:36:25

John Wilhelm
2019-01-26 06:37:57

Peter Ede
2019-01-26 07:57:22

Patrick Smith
2019-01-26 11:22:54

Shawn Atlas
2019-01-26 13:15:03

Gazsó Péter
2019-01-26 23:23:21

原文網址 DeMarcus Brownie Klamecker
2019-01-26 01:46:51

Anybody tried that? Seems new

翻譯年糕

Simone Bob Riolo
2019-01-26 01:52:23

Robert Silvers
2019-01-26 01:54:49

DeMarcus Brownie Klamecker
2019-01-26 02:10:45

Robert Silvers
2019-01-26 02:12:45

Aaron Swickard
2019-01-26 02:15:26

Chris Marshall
2019-01-26 02:17:06

Daniel Neubacher
2019-01-26 05:25:36

DeMarcus Brownie Klamecker
2019-01-26 05:34:37

Rob Mayberry
2019-01-26 07:20:06

Rob Mayberry
2019-01-26 07:20:25

Nick Santana
2019-01-26 09:16:59

Ryan Gamble
2019-01-26 10:55:24

DeMarcus Brownie Klamecker
2019-01-26 14:27:26

Ken Lim
2019-01-26 15:35:12

El Ner Endem
2019-01-26 15:40:58

Scott Young
2019-01-26 16:23:46

Scott Young
2019-01-26 16:24:00

Bryan Mikolajewski
2019-01-26 23:46:24

Mason Combs
2019-01-28 23:08:33

DeMarcus Brownie Klamecker
2019-01-28 23:29:10

Mason Combs
2019-01-28 23:29:35

DeMarcus Brownie Klamecker
2019-01-28 23:29:58

原文網址 Shreyo Bagchee
2019-01-26 00:42:20

Any tips on how to clean off a very thin hardened layer of resin off the FEP? It's so thin (maybe a 0.25mm) I'm having trouble lifting it with the spatula tool.

Additionally any tips to prevent that from happening again? Recalibrate/paper tighten the build plate?

翻譯年糕

Bobby Whitcomb
2019-01-26 00:43:50

Terry Reed
2019-01-26 02:21:43

Stefan Giudici
2019-01-26 05:47:02

Ken Lim
2019-01-26 14:45:56

Terry Reed
2019-01-26 14:54:36

原文網址 Daniel Montmorency
2019-01-26 00:08:54

Jewel Marori inspiration print white resin just as demo will try to print them in castable resin to cast in sterling!

翻譯年糕

Daniel Montmorency
2019-01-26 00:10:04

Mark Wardle
2019-01-26 00:21:13

Daniel Montmorency
2019-01-26 00:23:30

原文網址 Gary Hunt
2019-01-25 23:40:50

Last night’s print... Anycubic green, .03 layer height, either 7 or 8 second exposure (I can’t remember!), printed at 45 degrees back, no hollowing. Primed in Tamiya light grey. 4hr, 56m print time.

翻譯年糕

原文網址 Zalrohg Lekgolo
2019-01-25 23:34:50

what happens if I print and its a tiny bit outside the line? i measured and i know the Build plat is big enough. Will it just refuse to save/print?

翻譯年糕

Markus Rahn
2019-01-25 23:43:28

Scott Avis
2019-01-25 23:45:52

Mike Cousins
2019-01-25 23:49:02

Zena Andreou
2019-01-25 23:52:50

Zena Andreou
2019-01-25 23:54:14

Martin Souček
2019-01-25 23:57:56

Ben Vagg
2019-01-26 00:02:39

Richard Shapiro
2019-01-26 00:11:28

Holden8702
2019-01-26 00:36:36

Sean Poeschl
2019-01-26 02:46:04

Ken Lim
2019-01-26 14:51:43

Sen Kun
2019-01-26 16:04:30

Susan Sioux Mercer
2019-01-28 14:22:04

Sen Kun
2019-01-28 15:34:30

Vinicius Silva
2019-01-28 18:08:37

Susan Sioux Mercer
2019-01-28 19:29:22

Susan Sioux Mercer
2019-01-28 19:32:16

Vinicius Silva
2019-01-28 20:58:11

Vinicius Silva
2019-01-28 20:59:48

Vinicius Silva
2019-01-28 21:02:04

Susan Sioux Mercer
2019-01-28 21:58:00

Vinicius Silva
2019-01-28 22:44:16

原文網址 Arnie Locsin
2019-01-25 23:32:23

My very first print (Battletech Timberwolf) and the power supply died mid print. Can't help but think this would have come out pretty nice (though thinking if I overdid the supports). Anyway, wanted to thank everyone who contribute here --- because of your comments, suggestions and tutorials, I was able to level the bed correctly and got the print to stick to the build plate. You folks are awesome!

翻譯年糕